Free tool

Deck and fence stain price calculator

Enter the deck, railing, stairs or fence, your prep and your crew's pace. You get gallons, hours, job cost and three prices at your margin.

Adrian GluchowskiOwner of Superior Stain Solutions, builder of ChalkLast reviewed

The job

Fill in what the job has and leave the rest at 0.

Product
Production rates

Typical starting points, adjust to your crew. Time a few jobs and put in your own numbers.

Your numbers
Good, better, best

Three ways to do the same job. Each is priced at your margin.

Good

Better

Best

-

Good

-
Gallons to buy
-
Labor hours
-
Materials
-
Labor
-
Overhead
-
Job cost
-
Profit
-

Better

-
Gallons to buy
-
Labor hours
-
Materials
-
Labor
-
Overhead
-
Job cost
-
Profit
-

Best

-
Gallons to buy
-
Labor hours
-
Materials
-
Labor
-
Overhead
-
Job cost
-
Profit
-

Pricing a stain job by the square foot of deck floor misses most of the work. Railings and stairs eat time far out of proportion to their size, prep changes the hours more than the stain does, and a second coat doubles the product but not the setup. This calculator prices each part on its own, then gives you three prices at the margin you set.

How the calculator works

  1. Stain area. It adds up every surface that gets stain: the deck floor, the railing (linear feet times the surface per foot), the stairs (steps times width times 1.5 feet for tread and riser) and any fence (length times height times one or two sides).
  2. Gallons. Stain area times coats, plus your waste allowance, divided by the coverage per gallon. It rounds up to whole gallons, because that is what you buy.
  3. Labor hours. Prep hours (stain area divided by the prep rate for wash, strip or sand), plus the time for each coat on the floor, railing, stairs and fence, times the number of coats, plus setup and cleanup. Hours round to the nearest tenth, and those rounded hours are the ones priced.
  4. Price. Labor plus materials is your direct cost. The price is that cost divided by one minus your overhead and margin, so both come out as a share of the price.

The formula

  • Stain area = deck + (railing ft x surface per ft) + (steps x stair width x 1.5) + (fence length x height x sides)
  • Gallons = stain area x coats x (1 + waste) / coverage, rounded up
  • Hours = prep area / prep rate + coats x (floor + railing + stairs + fence time per coat) + setup
  • Direct cost = hours x labor cost per hour + gallons x stain price + other materials
  • Price = direct cost / (1 - overhead% - margin%)

Why divide instead of adding a percentage? Adding 20% to a cost gives you a 20% markup, which is only a 16.7% margin. Dividing by one minus the margin gives you the margin you asked for. The markup vs margin calculator shows the difference on your own numbers.

Worked example

The calculator opens on this job: a 320 sq ft deck, 40 feet of railing and 4 steps at 4 feet wide. Labor costs you $35 an hour, overhead is 15% and you want a 20% margin.

Stain area: 320 (floor) + 160 (40 ft of railing at 4 sq ft a foot) + 24 (4 steps x 4 ft x 1.5 ft) = 504 sq ft.

The better option (wash, 2 coats, $55 a gallon stain):

  • Gallons: 504 x 2 x 1.10 / 200 = 5.5, so you buy 6. That is $330 of stain plus $25 of other materials, $355 in all.
  • Hours: wash prep is 504 / 300 = 1.7 hours. One coat is 2.13 hours on the floor (320 / 150), 3.33 on the railing (40 / 12) and 0.33 on the stairs (4 x 5 minutes), 5.8 hours. Two coats is 11.6. Add 1.5 for setup and the job is 14.8 hours.
  • Labor: 14.8 x $35 = $518. Direct cost: $518 + $355 = $873.
  • Price: $873 / (1 - 0.15 - 0.20) = $1,343.08. Overhead is 15% of that ($201.46), so the job costs you $1,074.46 and leaves $268.62 profit, exactly 20%.

All three options on the same deck:

OptionPrep and coatsHoursPriceProfit
GoodWash, 1 coat, $40 stain9.0$707.70$141.54
BetterWash, 2 coats, $55 stain14.8$1,343.08$268.62
BestSand, 2 coats, $70 stain21.5$1,842.32$368.47

Look at the railing. It is 40 feet, but at 12 feet an hour per coat it takes more time than the whole floor. That is why a per-square-foot price that only counts the floor loses money on railing-heavy decks.

This calculator's starting numbers are typical defaults and differ from the worked example in How to price a deck stain job; put in your own.

Gallons of stain by deck size

How many gallons of stain does a 12x12 deck take? It depends on how far a gallon goes on your boards. The tables below cover the floor of the deck only, for the sizes people ask about most, at three coverage figures and with the calculator's 10% waste allowance. Numbers are whole gallons, rounded up, because that is what you buy. A deck that needs 1.06 gallons is a 2 gallon job.

One coat

DeckFloor area150 sq ft/gal200 sq ft/gal300 sq ft/gal
10 x 10 ft100 sq ft111
12 x 12 ft144 sq ft211
12 x 16 ft192 sq ft221
16 x 16 ft256 sq ft221
16 x 20 ft320 sq ft322
20 x 20 ft400 sq ft332

Two coats

DeckFloor area150 sq ft/gal200 sq ft/gal300 sq ft/gal
10 x 10 ft100 sq ft221
12 x 12 ft144 sq ft322
12 x 16 ft192 sq ft332
16 x 16 ft256 sq ft432
16 x 20 ft320 sq ft543
20 x 20 ft400 sq ft653

Which column to use. Use the coverage on your stain's data sheet. Semi-transparent and solid stains do not cover the same, and they do not call for the same number of coats, so the data sheet decides both. As a guide, bare, rough or weathered boards drink stain and sit near 150. Smooth, sound wood sits nearer 300. The calculator starts at 200. Penofin lists 150 to 200 sq ft a gallon on rough wood and 250 to 300 on smooth, and Sherwin-Williams lists about 250 to 350 (sources below).

What the tables leave out. Railings, stairs, skirting and fascia take stain too. A 16 x 20 deck with 40 feet of railing and four steps needs more than the floor figure says. Enter the full deck above and the calculator adds each part. Wood that has just been stripped or sanded takes more on the first coat than the data sheet's number.

Where the starting numbers come from

  • Coverage, 200 sq ft a gallon. Penofin lists 150 to 200 sq ft a gallon on rough wood and 250 to 300 on smooth. Sherwin-Williams' deck planning guide says about 250 to 350, depending on the wood. A weathered deck floor drinks more than new siding, so 200 is a careful middle. Use the number on your product's data sheet, and lower it for old, gray or rough boards.
  • Stair depth, 1.5 feet a step. The model residential code (IRC R311.7.5) allows risers up to 7 3/4 inches and treads of at least 10 inches, so a tread and riser together run about 18 inches.
  • Production rates, railing surface and setup time are typical starting points, not published figures. Adjust them to your crew. The best numbers you will ever have are your own: time three jobs and use the averages.

Common mistakes

  • Only measuring the floor. Railings, stairs, skirting and the fascia under the deck all take stain and time. Price each one.
  • Using the best coverage on the can. Coverage on the label is usually for smooth, sound wood. Old decks soak up more, and the first coat on stripped wood soaks up the most.
  • Treating every coat the same. Some penetrating stains are one coat only, or go on wet on wet. Check the product's directions before you sell a second coat, and set the coats to match.
  • A wage instead of a labor cost. $20 an hour in wages costs you more once payroll taxes, workers comp and drive time are in. The hourly rate calculator works out your loaded cost.
  • Forgetting the small-job floor. Setup, travel and cleanup are the same on a 100 sq ft landing as on a big deck. Keep a minimum price and do not quote under it.
  • Skipping prep chemicals. Stripper, brightener and cleaner are real costs on a strip job. Put them in other materials.

How to use this in a quote

Chalk quotes do not hold separate good, better and best packages. What they hold is optional extras: lines your customer ticks or leaves on their phone, with the total updating as they go. That works well for step-up pricing:

  1. Put the good option on the quote as the main line, at the good price.
  2. Add each step up with + Optional extra and price it at the difference. In the example, "Second coat and better stain" is $635.38 (better minus good). Tick We recommend it on the one you want them to pick.
  3. Extras add up on their own, so write each one so it makes sense by itself. A sanding upgrade is clearest as its own extra with its own price.

Two more things that help close a stain job:

  • Deposit to collect on the quote asks for a percentage or a flat amount, and the customer pays it when they approve.
  • A Timed offer puts a dollar or percent discount on the quote with a countdown on the customer's page. The clock starts when you send the quote (sending it again restarts it), and approving while it runs locks the discount in. It suits an off-season or book-this-week push.

Here is how to send a quote and get it approved in Chalk.

Sources