Pressure washing has the lowest barrier to entry of any exterior trade, and the most price pressure. Customers compare you to a neighbor with a rental machine and to every guide on the internet. The way to hold your price is to know your costs cold: your machine, your chemicals, your drive time and your minimum.
This guide is about the pricing decisions: which model to quote in, what the market pays, what a crew hour really costs you, where to price between your cost floor and the market, the minimum, surcharges and add-ons, two-story houses, decks and bin-cleaning routes. The math for one job, with worked examples for a house wash, a driveway and a deck, is on the pressure washing price calculator.
Just starting out? The first 90 days of a pressure washing business covers insurance, gear, safety and your first customers.
What customers see online
Fixr's guide to pressure washing a house (updated January 2025) is typical:
| What | Fixr's range |
|---|---|
| Pressure washing, per sq ft | $0.30 to $0.80 |
| Power washing, per sq ft | $0.35 to $0.70 |
| Soft washing, per sq ft | $0.25 to $0.35 |
| Hourly rate | $50 to $150 |
| Common minimum charge | $100 to $350 |
| Whole house, typical | $500 to $900 (average $700) |
| Concrete / vinyl / wood, per sq ft | $0.30 to $0.33 / $0.30 to $0.40 / $0.30 to $0.50 |
And for common add-on surfaces, from the same page and Fixr's driveway and deck pages:
| Surface | Typical total |
|---|---|
| Driveway, 600 sq ft | $180 to $240 ($0.30 to $0.40 per sq ft, hot water $0.40 to $0.55) |
| Deck, 500 sq ft | $150 to $200 |
| Fence | $125 to $235 |
| Patio, 50 sq ft | $50 to $75 |
| Gutters | $200 to $400 |
| Roof | $450 to $700 |
These are national averages. Your market may be higher or lower, and customers will quote them to you. Use them as a check after you build your price.
The three ways to price
| Model | How it works | Good for | Watch out for |
|---|---|---|---|
| Per square foot | Area x your rate for that surface | Flatwork, siding, fences | Dirty or hard surfaces take longer per foot than clean ones |
| Flat rate | A set price per job type | Repeat jobs you have timed (a standard driveway, a patio) | Odd sizes and conditions |
| Hourly | Time x rate | Odd jobs, add-ons, cleanup | It penalizes your speed. A faster crew earns less. |
Most shops quote per square foot or flat rate, then check it against an hourly figure and apply a minimum.
Step 1: Measure and look
- Area. Length x width for flatwork. For siding, walls only, with openings left in unless they are large.
- Material. Concrete, brick, wood, vinyl, stucco, composite. Fixr's page lists a lower suggested pressure for wood (1,000 to 1,500 psi) than for concrete (3,000 to 3,500 psi). Match the method to the surface and be careful with soft materials.
- How dirty. Light dust, green algae, black mildew, rust, oil, gum, paint. Photograph what you see.
- Height and access. Two stories, steep ground, plants, a gate that is locked, a water source that is far away.
- Water. Does the customer have a working spigot and pressure? Fixr notes water costs about $2 an hour.
- Where the water goes. See the wastewater note below.
Step 2: Production rates
Nobody publishes an official rate table for pressure washing, and the numbers you will find vary a lot. Here is what exists, labeled by quality:
| Source | Rate |
|---|---|
| Estimating guide (CompositePaint) | Pressure washing siding: 800 to 1,200 sq ft per painter-hour |
| One estimating program's default | One example assembly with a detergent wash runs 400 sq ft per hour |
| Contractor forum (Pressure Washing Resource, 2014) | About 1,500 sq ft per hour for a 20 inch surface cleaner on a 4 gpm, 4000 psi machine. One commercial contractor says 3,000 to over 10,000 sq ft per person-hour with 24 to 48 inch cleaners on hot-water units of 8 gpm or more. |
Those can all be true, because machines, surfaces and dirt differ. So time yourself. On your next five jobs, record these separately: drive time, setup, pre-treat, wash, rinse, cleanup. Divide the area by the hours for each surface type. Test a 10 by 10 foot section before you quote an unusual surface.
Step 3: Know your equipment cost per hour
Your machine, surface cleaner, hoses, trailer or truck, and chemicals wear out. Charge for it.
Equipment cost per hour = (purchase price - expected resale value) / expected hours of life + fuel and maintenance per hour
Add the cost of chemicals per job, insurance and the truck. If you use a rig that you use half the year, spread the cost across the hours you actually run it. Your accountant or your tax software has your real numbers.
Step 4: What a crew hour costs you
Labor cost is wage plus burden. The Bureau of Labor Statistics lists $23.75 an hour as median pay for painters in May 2025 (one reference point, since washing crews are paid differently), and one estimating guide puts payroll taxes, workers' compensation and the rest at 25% to 40% of wages. Add your equipment cost per hour from Step 3 and you know what one crew hour really costs you.
That hourly cost, your chemical cost per 100 sq ft, your setup time and your minimum are the inputs to the pressure washing price calculator, which turns them into a price at your overhead and margin. To carry the machine in the price, add its cost per hour to the labor cost you enter. Why the price divides by one minus overhead and margin instead of adding a markup is in How to price a deck stain job.
Your cost is the floor, the market is the ceiling
A price built from cost tells you the least you can charge. The published ranges tell you what homeowners pay across the country. In washing the two are often far apart. With the calculator's example inputs, a 2,200 sq ft house wash has a floor of $325, while Fixr's soft wash range of $0.25 to $0.35 a square foot puts the same wall area at $550 to $770. See the house wash example.
Where you price between the two is a decision, not a formula.
| Toward the top of the range | Toward your floor |
|---|---|
| You carry insurance and put the job in writing | You are new, with few reviews or photos yet |
| You book out two weeks or more | A slow week you need to fill |
| Delicate work: roofs, painted siding, old wood | Plain concrete on a dense route with a short drive |
| You answer fast and show up when you say | A repeat customer on a yearly plan |
Two habits keep the base price healthy. First, when you need to fill a gap, use a dated offer instead of lowering your price for everyone; a discount that ends is easier to take back than a price. Second, when you are booked out past a few weeks, raise prices for new quotes. How to raise your prices covers how to tell existing customers. Giving the customer a choice, a house wash alone, with the driveway, or with the driveway and sealing, often sells the middle option; see good, better, best pricing.
Setting your minimum charge
The minimum is the price of rolling the truck. It should cover the round-trip drive, setup, a short wash and cleanup at your full margin. Fixr says minimums of $100 to $350 are common. The drive-time cost calculator shows what the trip alone costs, and the calculator's driveway example shows a 600 sq ft driveway whose work adds up to $107.51 landing on a $225 minimum.
- Say it up front, on your website, your booking form and the phone: "Our minimum is $225, which covers the trip and setup." A customer who knows the minimum before the visit does not feel tricked by it.
- Fill the minimum instead of discounting it. If a small job comes in under it, offer what fits inside: the front walk, the patio steps, the trash cans. The customer gets more for the same money and you keep your price.
- Charge more off your route. Set a service area, and add a trip charge or a higher minimum beyond it.
- Never waive it for a quick job. Quick jobs are what the minimum is for.
- Review it every season, as fuel, wages and insurance move.
Surcharges and add-ons
Price the surface you see, not an average one. Name each of these as its own line on the quote, so the customer sees what they are paying for and why it costs more than the neighbor's:
- Oil, rust, gum, paint or heavy black mildew. Pre-treat, specialty chemicals and extra passes. Hot water costs more to run, and Fixr's hot water driveway range is $0.40 to $0.55 a square foot against $0.30 to $0.40 cold.
- No water on site. Bringing water is setup time and gear.
- Height and access. Second stories, steep ground, locked gates and long hose runs.
- Containment. Where stormwater rules ask for it, blocking drains and recovering water is real time and gear (see the wash water warning above).
The add-ons worth offering on the same visit are concrete or paver sealing (how to price paver and concrete sealing; Fixr lists driveway sealing at $0.88 to $2.10 a square foot), a roof soft wash (how much to charge for roof cleaning), the fence, gutter brightening, windows and trash cans. Every add-on on the same trip shares the drive and setup you have already paid for, which is where the margin is. More ways to offer them without a hard sell are in upsells and add-ons for service contractors.
Driveways
A driveway is a job customers often shop on price. Fixr lists $0.30 to $0.40 per sq ft for a driveway, $0.40 to $0.55 with hot water, and about $225 for a 600 sq ft driveway. Because the market price for a standard driveway sits in a narrow band, many shops sell it at a flat rate ("two-car driveway and front walk") once they have timed a few.
- Quote the walks with it. A 4 by 40 foot sidewalk adds 160 sq ft of minutes, not a second trip.
- Hand work is the slow part. Edges, steps and the strip along the garage door take longer per foot than the open slab under a surface cleaner. Allow for them.
- Check the drainage before you start. Wash water runs to the street and the storm drain.
- Stained, sealed or spalling concrete is a separate quote. If the customer wants it sealed, see paver and concrete sealing.
The numbers for one driveway, every input shown, are in the calculator's 600 sq ft driveway example.
A two-story house
A two-story house does not cost twice as much as a one-story house with the same floor plan, but it costs a lot more. The wall area doubles, and the second story is slower per foot, because you work from ladders, an extension pole or a lift, and every move takes time.
Wall area = perimeter x height x stories, plus the gables
Take a house with a 26 by 38 foot footprint (perimeter 128 feet), a 6 in 12 roof and gables on the 26 foot ends, which is 169 sq ft of gable. As a one-story house the walls are 128 x 9 = 1,152 sq ft, and as a two-story 128 x 18 = 2,304 sq ft. Add the gables for 1,321 and 2,473 sq ft. See How to measure a house for exterior painting for the formulas.
Price the second story by its pace, not by a flat upcharge. Time how much slower you are on ladders or a pole, and lower the production rate you use to match. In the calculator's house wash example, slowing from 500 to 350 sq ft an hour lifts the floor from $325 to $420. The shared drive, setup and cleanup are why the price per square foot falls as the house gets bigger, even though the total rises. Fixr's whole-house range is $500 to $900. Third stories and steep roofs call for a lift or a different method, and are a different quote.
Ladder safety applies. See the ladder rules in How much to charge for gutter cleaning.
A deck
Fixr lists $150 to $200 for pressure washing a 500 sq ft deck (see the table above). A deck on its own is hard to sell at a fair price: in the calculator's 400 sq ft deck example, half the price is the drive and setup. Sell it with the house wash where you can. Wood is softer than concrete, so the machine, the pressure and the technique are different from a driveway. The DEFY Extreme data sheet caps rinsing pressure at 1,200 psi, and Fixr suggests 1,000 to 1,500 psi for wood. Too much pressure raises the grain and scars the boards.
Two points matter for your price:
- Is it a wash, or the first step of a staining job? If the customer will have the deck stained afterward, the wash is part of the stain price, and the wood has to dry before stain goes on. The data sheets give 24 to 48 hours or more. See Weather rules for exterior painting and staining. That wait is a second trip.
- Wash only, with a stain recommendation. If the customer just wants the deck washed, say so on the quote: "Washing does not seal or protect the wood. It will gray again."
The pricing for the staining side, including the wash-and-stain and sand-and-stain options, is in How to price a deck stain job.
Trash cans
Trash can cleaning is a small route business that some washers add. It is priced per can, and the money is in the route, not the can. Bubble Binz, a bin-cleaning operator, publishes these ranges per bin, per cleaning: one-time deep clean $35 to $60, every four weeks $18 to $25, every six weeks $22 to $28, every 8 to 12 weeks $25 to $32. It says extra bins at the same house add about $4 to $10 each, because the truck is already there. That is one company's price list, not a market survey.
Work out your own from the stop:
Placeholders: one operator at $26 an hour, a truck-mounted unit at $20 per hour, 8 minutes per bin, 12 minutes between stops on a dense route, $1.50 of chemicals and water per stop, overhead 20% and profit 15%.
| Item | Working | Amount |
|---|---|---|
| Time per stop, two bins | 2 x 8 + 12 minutes = 28 minutes | 0.47 h |
| Labor | 0.47 h x $26 | $12.13 |
| Truck and unit | 0.47 h x $20 | $9.33 |
| Chemicals and water | $1.50 | |
| Direct cost | $22.97 | |
| Price per stop = $22.97 / 0.65 | $35.33 | |
| Per bin | $35.33 / 2 | $17.67 |
At 28 minutes a stop, a full day is about 17 stops. If the stops are not dense, the 12 minutes becomes 25 and the price per bin rises to about $25. Price for route density: a customer two streets from your route is worth more than one across town. Set a service radius, charge a sign-up fee for stops off your route, and offer a better per-bin price for four-week service than for one-time. Frequency makes the route work.
Common mistakes
The costliest mistake is damaging the surface you were hired to clean. See when you damage a customer's property for what to do and what your insurance may not cover.
- Charging for the machine's time and forgetting the drive. Travel and setup are real cost.
- Pricing to the rental place. Customers compare you to a day's rental, but you bring a clean result, insurance and speed.
- No minimum. Your smallest job still costs a trip.
- Not looking at the dirt. Oil, rust, black mildew and gum are extra lines. Name the surcharge up front.
- Using one pressure for every surface. Soft surfaces get damaged. A damage claim erases a month of profit.
- Ignoring where the water goes. See the warning above.
- Washing and staining on a calendar that ignores the weather. See Weather rules for exterior painting and staining.
- Hourly pricing that punishes speed. If you get faster, a fixed price pays you for it.
- Markup instead of margin. See the table in the deck guide.
Put your terms in writing with the free pressure washing contract template.
How Chalk helps
This part is about our software.
- Price book. Add your washing lines with a unit (sq ft, each, hour) and your price per unit, and your minimum as a line of its own. Pick them on the quote. See Send a quote and get it approved.
- Digital quote and invoice. Send the quote and invoice as links the customer can open on a phone. Customers can pay the invoice by card or bank transfer once you have online payments set up.
- Quote follow-ups. You can turn on follow-ups for quotes that go quiet, which are off until you turn them on.
Looking for a quick number? Try the pressure washing price calculator. Need an invoice to hand over? Use the contractor invoice template.
Sources
Prices and rates change and vary by region. Check the current version of each source.
- Fixr: cost to pressure wash a house, driveway and deck, all updated January 31, 2025.
- CompositePaint: how to estimate a paint job. An estimating guide; its siding wash rate is a starting point only.
- Pressure Washing Resource: square feet per hour. Contractor forum posts from 2014, used as color only.
- Bubble Binz: trash can cleaning cost. A bin-cleaning operator's price list; used as one example.
- DEFY Extreme Wood Stain product data sheet, 2020: the 1,200 psi rinsing limit for wood.
- EPA: stormwater best management practice, vehicle maintenance and washing, February 2023.
- U.S. Bureau of Labor Statistics: painters, construction and maintenance.