Free tool

Paint estimate calculator

Walls, ceilings, trim and doors in. Gallons to buy, hours, job cost and a price at your margin out. Works inside or out.

Adrian GluchowskiOwner of Superior Stain Solutions, builder of ChalkLast reviewed

What you are painting

Works the same inside or out: siding is wall area, soffit is ceiling area, fascia and corners are trim.

Paint
Production rates

Typical starting points, adjust to your crew. Time a few jobs and put in your own numbers.

Your numbers

Price

-
Labor hours
-
Materials
-
Labor
-
Overhead
-
Job cost
-
Profit
-

Paint to buy

Walls
-
Ceilings
-
Trim and doors
-
Paint cost
-

Where the hours go

Walls
-
Ceilings
-
Trim
-
Doors
-
Prep and setup
-

A paint job is four different jobs sharing one ladder: walls, ceilings, trim and doors. They use paint at different rates and go at very different speeds. Walls are fast and use most of the paint. Trim and doors are slow and use very little. Price them together by the square foot and you end up cheap on trim-heavy rooms and high on open, plain ones. This calculator keeps them apart.

How the calculator works

  1. Measure each part. Wall area is the room's perimeter times the wall height, less big openings like a garage door or a wall of windows. Ceiling area is length times width. Trim is linear feet of base, casing and crown. Doors are a count, both sides and edges. Outside, siding is wall area, soffits are ceiling area, and fascia and corner boards are trim.
  2. Gallons for each paint. Area times coats, plus waste, divided by coverage. Trim uses linear feet per gallon and doors use doors per gallon. Trim and doors share one paint. Each paint rounds up to whole gallons.
  3. Hours. Each part's quantity divided by its production rate, times its coats. Doors are hours per door per coat. Prep, setup and cleanup go on top. The total rounds to the nearest tenth of an hour, and that is what gets priced.
  4. Price. Labor plus paint plus sundries is your direct cost. The price is direct cost divided by one minus overhead and margin.

The formula

  • Wall gallons = wall sq ft x coats x (1 + waste) / coverage, same for ceilings
  • Trim and door gallons = trim ft x coats x (1 + waste) / ft per gallon + doors x coats x (1 + waste) / doors per gallon
  • Hours = walls / rate x coats + ceilings / rate x coats + trim / rate x coats + doors x hours per door x coats + prep
  • Price = (hours x labor cost + paint + sundries) / (1 - overhead% - margin%)

Worked example

The calculator opens on a typical repaint: 1,200 sq ft of walls at 2 coats, 400 sq ft of ceilings at 1 coat, 250 feet of trim and 6 doors at 2 coats. Labor costs $35 an hour, overhead is 15% and the target margin is 20%.

Paint:

  • Walls: 1,200 x 2 x 1.10 / 350 = 7.5 gallons, so 8 at $45 = $360.
  • Ceilings: 400 x 1 x 1.10 / 350 = 1.3 gallons, so 2 at $35 = $70.
  • Trim and doors: 250 x 2 x 1.10 / 500 = 1.1, plus 6 x 2 x 1.10 / 8 = 1.65, so 2.75 gallons and you buy 3 at $55 = $165.
  • With $60 of sundries, materials are $655.

Hours:

  • Walls: 1,200 / 150 x 2 = 16 hours.
  • Ceilings: 400 / 120 = 3.3 hours.
  • Trim: 250 / 40 x 2 = 12.5 hours.
  • Doors: 6 x 0.5 x 2 = 6 hours.
  • Prep and setup: 4 hours. Total 41.8 hours, or $1,463 of labor.

Price: ($1,463 + $655) / (1 - 0.15 - 0.20) = $2,118 / 0.65 = $3,258.47. Overhead at 15% of the price is $488.77, the job costs you $2,606.77 and the profit is $651.70.

The lesson is in the hours. Trim and doors are 18.5 of the 37.8 painting hours, nearly half the labor, for 3 of the 13 gallons. A room with lots of casing and six-panel doors is a different price from a plain room the same size.

This calculator's starting numbers are typical defaults and differ from the worked examples in How to price exterior painting and How to price interior painting; put in your own.

Gallons of exterior paint by house size

How many gallons of paint does a 2,000 sq ft house need? A quick answer, for the house sizes people ask about most, is in the tables below. They are a planning figure for the siding of a simple house, not a replacement for measuring. The paint is for walls only, at 350 sq ft a gallon with the calculator's 10% waste allowance, rounded up to whole gallons.

How the wall area is worked out. The house is a rectangle 1.5 times as long as it is wide. The footprint is the living area for one story and half of it for two stories. The walls are 9 feet a story. The tables take off 15% of the wall for windows and doors. So a 2,000 sq ft one story house has about 1,397 sq ft of wall to paint.

Living areaOne story: wall1 coat2 coatsTwo story: wall1 coat2 coats
1,200 sq ft1,082 sq ft471,530 sq ft510
1,500 sq ft1,210 sq ft481,711 sq ft611
1,800 sq ft1,325 sq ft591,874 sq ft612
2,000 sq ft1,397 sq ft591,975 sq ft713
2,400 sq ft1,530 sq ft5102,164 sq ft714
2,500 sq ft1,562 sq ft5102,208 sq ft714
3,000 sq ft1,711 sq ft6112,419 sq ft816

What the tables leave out. Gable ends, soffits, fascia, trim, doors, a garage or porch that sticks out, and any stucco or rough surface that takes more paint than the data sheet's number. A house with a lot of trim or a complex shape will need more than the table says. Measure the real house, enter the walls, trim and doors above, and use the calculator's number for the quote. If you are using a different coverage than 350, scale the gallons: at 250 sq ft a gallon, the numbers go up by about 40%.

Where the starting numbers come from

  • Coverage, 350 sq ft a gallon. Paint makers publish a spread rate on each product's data sheet. Sherwin-Williams lists 350 to 400 sq ft a gallon for its Resilience exterior latex at the recommended film thickness, and Benjamin Moore lists 250 to 350 for its Regal Select exterior high build. Many interior wall paints list a similar range. Rough siding, stucco, block and fresh drywall all take more, so use your product's sheet and lower it for porous surfaces.
  • Trim coverage, doors per gallon and production rates are typical starting points, not published figures. Adjust them to your crew and the work. Brush and roll, spray, new work and repaints all move at different speeds.

Common mistakes

  • One price per square foot of floor. It hides the trim and door count, which is where the hours are. Count doors and measure trim.
  • Using the data sheet rate on a rough surface. The printed rate is for a smooth, sealed surface at the stated film thickness. Bare wood, patched walls and textured surfaces can take a primer coat and still use more.
  • Counting coats for paint but not for time. A second coat on trim is nearly as slow as the first. The calculator multiplies hours by coats for every part.
  • Leaving prep at zero. Moving furniture, masking, patching, caulking and daily cleanup add up. On exteriors, scraping and washing can be a day by themselves.
  • Forgetting lead rules on older homes. If you are paid to disturb paint in a home built before 1978, the EPA's Renovation, Repair and Painting rule requires a certified firm and lead-safe work practices. That changes your prep time and materials.
  • Missing rentals. Lifts, tall ladders and sprayers are real job costs. Add them to sundries.

How to use this in a quote

Write the quote the way you priced it, one line each for walls, ceilings, trim and doors. Your customer sees what is included, and you can change one line without redoing the whole price.

  • Anything the customer might add, such as ceilings, closets or an accent wall, can go on as an optional extra with + Optional extra. They tick it on their phone and the total updates.
  • Set Deposit to collect to a percentage or a flat amount. The customer pays it when they approve.
  • A Timed offer adds a dollar or percent discount with a countdown on the customer's page, counted from when you send the quote.

Here is how to send a quote and get it approved in Chalk.

Sources