Pricing guide

How to price exterior painting

Bid an exterior paint job from a takeoff: siding, trim, doors and prep. Data sheet coverage, cited production rates and worked examples with every input.

Adrian GluchowskiOwner of Superior Stain Solutions, builder of ChalkLast reviewed 16 min read

On this page

An exterior paint job is won or lost on three things: how well you measured, how honest you were about prep, and how long the trim took. The paint itself is the smallest part of the cost.

This guide walks through measuring a house, pricing prep, working out paint from the maker's coverage, turning hours into labor cost, and arriving at a price that pays your overhead and leaves a profit. It has a worked example priced by hand, the same house run through the free paint estimate calculator with every input shown, a table of what moves the price, and the mistakes that cost painters the most. Pricing rooms instead? See How to price interior painting.

What homeowners see online

Fixr's guide to painting a house exterior (updated January 2025) gives a typical customer's picture:

WhatFixr's range
Exterior walls, per sq ft$2.84 to $5.28
Trim, per linear foot$2.15 to $3.99
A 2,200 sq ft whole-house job$6,242 to $11,617
Wood, vinyl or fiber cement siding, per sq ft$3.10 to $5.80
Stucco, per sq ft$2.70 to $5.05

Fixr says its prices include standard prep such as sanding, caulking, power washing and masking, and that walls in poor condition can cost over 60% more. Use ranges like these as a check after you have priced the job from your own costs. They are national averages, not your market.

Step 1: Measure the house

Do a takeoff on paper. Do not price from square footage of the floor plan. The full walk-around order, the formulas for gables and trim, and a field sheet are in How to measure a house for an exterior paint estimate.

PartHow to measureNotes
Siding wallsPerimeter x average wall height, summed for each wallTwo stories: measure each story.
GablesBase x height / 2 for each triangleAdd to the walls.
OpeningsWindows and doors you will not paintOne estimating guide says to deduct only openings larger than about 50 sq ft (CompositePaint). Pick a rule and use it every time.
TrimLinear feet of window and door casing, corner boards, fascia, rakes, soffitCount soffit as sq ft if you are painting it.
DoorsCount each; note panel or flat, one side or twoFront doors take longer than you think.
Garage doors, shutters, railings, ventsCount or measure eachPrice as separate lines.

Walk the house and note what changes the price: stories and ladder reach, steep ground, shrubs against the walls, a second color, bare wood, peeling, cracked caulk, masonry and aluminum.

Step 2: Price the prep

Prep is most of the job on a repaint. It is also where bids go wrong, because prep is invisible in a quote. Write it in.

  • Wash. Dirt and mildew stop paint from sticking. One estimating guide lists 800 to 1,200 sq ft per painter-hour for pressure washing siding. If you subcontract it, see the pressure washing guide.
  • Scrape and sand failing paint. The same guide lists 40 to 80 sq ft per painter-hour for scraping and sanding failing exterior paint. Walk the house and estimate how many square feet are failing, and write that number on the estimate.
  • Caulk and patch. Count the joints. Cracked caulk and rotted wood are repairs, not paint.
  • Prime. Sherwin-Williams' Duration data sheet calls it self-priming on most surfaces, with two coats on new bare surfaces or one coat on a repaint. Knots, stains and chalky or bare wood still need a primer or a spot prime.
  • Glossy trim. Sherwin-Williams' Emerald Urethane Trim Enamel data sheet says glossy surfaces should be sanded dull before coating.

Step 3: Work out the paint

Use the maker's coverage, then be honest about the surface.

Product (data sheet)Coverage per gallonCoats and timing
Sherwin-Williams Duration Exterior Acrylic Flat250 to 300 sq ft (5.3 to 6.4 mils wet)Self-priming. One coat on a repaint, two on bare surfaces. Recoat in 4 hours at 45 F or warmer. Apply above 35 F.
Benjamin Moore Regal Select Exterior Soft Gloss (263)300 to 400 sq ft (5.3 to 6.0 mils wet), "depending on surface texture and porosity"Self-priming on most surfaces, but bleeding woods such as cedar and redwood get a primer. Recoat in 4 hours. Apply at 35 to 100 F surface temperature.
Sherwin-Williams Emerald Urethane Trim Enamel350 to 400 sq ft (4 mils wet)Recoat in 4 hours. Apply above 50 F.

Gallons for a surface = area x coats / coverage. Add about 10% for waste. Rough wood, stucco and masonry drink paint, so use the low end of the range, or lower. Where you are changing color from dark to light, plan for two finish coats and possibly a tinted primer.

Cost per gallon changes by brand, line and your supplier discount. Use your own price list.

Step 4: Production rates

There is no free table of exterior production rates from the paint makers. What is published comes from estimating guides and software. One of them (CompositePaint) lists these, per painter-hour per coat:

TaskRate
Exterior siding, brush and roll100 to 150 sq ft
Exterior siding, spray plus back-brush300 to 500 sq ft
Pressure wash siding800 to 1,200 sq ft
Scrape and sand failing paint40 to 80 sq ft

For trim, Fixr says it takes 30 to 60 minutes to paint 15 linear feet. Spraying siding is faster on paper, but masking can take hours. And coats are not all equal: one estimating program's default uses an example where 125 sq ft per hour for one coat becomes 85 sq ft per hour for two, which means the second coat goes faster than the first. That is an example, not a measured rate, but it is a good reason to time first and second coats separately.

Do not trust any of these over your own. Time your crew for five exterior jobs, split by task: wash, scrape and sand, caulk and patch, mask, spray or roll siding, brush trim, doors, cleanup. Use the slower average when you quote.

The rates in this guide's examples, and where each one comes from:

RateValue in the examplesSource
Wash siding1,000 sq ft/hrMiddle of CompositePaint's 800 to 1,200
Scrape and sand failing paint60 sq ft/hrMiddle of CompositePaint's 40 to 80
Spray and back-roll siding, per coat400 sq ft/hrMiddle of CompositePaint's 300 to 500
Brush and roll siding, per coat125 sq ft/hrMiddle of CompositePaint's 100 to 150
Trim, per coat30 ft/hr, and 15 or 20 in the what-if tableFixr's 15 linear feet in 30 to 60 minutes
Entry door, per coat0.75 hoursExample input (CompositePaint's own example uses 1.5 hours a door)
Caulk, patch, mask, set up, clean up23 hours in allExample allowance for this house, not a rate

If your crew's numbers are different, and they will be, change the inputs and the price changes with them.

Trim: windows, doors, fascia and soffit

Trim is where exterior bids go wrong, because trim is slow, detailed and counted in feet, not square feet. In the worked example below, trim is 28 of 77 hours.

Price trim by the linear foot, and measure it (casing, sills, corner boards, fascia, rakes) as described in the measuring guide. Fixr lists $2.15 to $3.99 per linear foot, and says it takes 30 to 60 minutes to paint 15 linear feet. That is a production rate of 15 to 30 feet an hour.

The rate is the swing factor. Using the worked example's labor rate of $32.50 an hour, two coats, $0.45 per foot for trim paint, caulk and prep, and 20% overhead with 15% profit (price is direct cost divided by 0.65):

Pace, per coatLabor per foot (two coats)Price per footA 16 ft window casing
15 ft/hr (Fixr's slow end)$4.33$7.36$118
22.5 ft/hr (middle)$2.89$5.14$82
30 ft/hr (Fixr's fast end, and the worked example)$2.17$4.03$64

At the fast pace the price sits at the top of Fixr's range, and at the slow pace it is nearly double. A crew that thinks it paints 30 feet an hour but really paints 20 will lose money on every house. Time your trim on five jobs.

What slows trim down:

  • Cutting in against siding, brick or glass. Masking or a steady hand costs minutes per window.
  • Height. Fascia and soffit on a second story means a ladder move every few feet.
  • Detail and glazing bars. Divided-light windows and profiles take far longer per foot.
  • Condition. Peeling, caulk failure and rot are separate lines.
  • Color change. Dark trim over light or the reverse means primer or an extra coat.

Soffit is measured in square feet (eave length times overhang), and fascia and rakes in linear feet. If you spray the soffit, include the masking. Doors are a count: price a front door at more than a flat one.

Trim paint is a different product from siding paint. Sherwin-Williams' Emerald Urethane Trim Enamel data sheet lists 350 to 400 sq ft per gallon, applies above 50 F, and recoats in 4 hours. Check the sheet for the trim paint you will use, including its temperature limit.

Step 5: From cost to price

Labor cost per hour is wage plus burden. The Bureau of Labor Statistics lists $23.75 an hour as median pay for painters in May 2025, and one estimating guide puts payroll taxes, workers' compensation and other costs at 25% to 40% of wages. Add labor, materials and equipment (lift or scaffold rental, spray tips, dump fees) to get direct cost. Then:

Price = direct cost / (1 - overhead % - profit %)

Divide, do not add a markup. The reasons, and a markup vs margin table, are in How to price a deck stain job. For a benchmark: the NAHB remodeler survey for 2024 found operating expenses averaged 23.6% of revenue and net profit 6.3%. One painting guide says small residential shops run 20% to 35% overhead and aim for 15% to 25% net.

Example: a two-story repaint, priced by hand

The job (Example): a two-story house with wood siding, repaint with a color change. Measured siding is 2,400 sq ft after openings, with 420 linear feet of trim, three entry doors and a two-car garage door. About 300 sq ft of siding has failing paint. The house was built in 1995, so the lead rule does not apply.

Placeholders: labor costs $32.50 an hour (a $25 wage plus 30% burden). Overhead is 20% of price and profit is 15%.

TaskQuantity and rateHours
Wash2,400 sq ft at 1,000 sq ft/hr2.4
Scrape and sand failing paint300 sq ft at 60 sq ft/hr5.0
Caulk, patch, spot primeallowance12.0
Mask and set upallowance8.0
Spray and back-roll siding, two coats4,800 sq ft of coats at 400 sq ft/hr12.0
Brush trim, two coats840 ft of coats at 30 ft/hr28.0
Entry doors3 at 1.5 hr4.5
Garage door12.0
Cleanup and touch-upallowance3.0
Total76.9

Materials and equipment:

ItemCost
Siding paint: 2,400 x 2 coats / 250 = 19.2 gal, 21.1 with waste, so 22 at $55$1,210
Trim, doors and garage door paint: 2 gal at $60$120
Primer for bare spots: 2 gal at $40$80
Caulk: 16 tubes at $7$112
Masking, plastic, tips, scrapers$120
Wash detergent$30
Lift and sprayer wear$250
Total$1,922

From cost to price:

ItemAmount
Labor, 76.9 h x $32.50$2,499.25
Materials and equipment$1,922.00
Direct cost$4,421.25
Price = $4,421.25 / 0.65$6,802
Overhead share (20%)$1,360
Profit share (15%)$1,020

That is $2.83 per sq ft of wall. Fixr's range is $2.84 to $5.28, so this price sits just under the bottom of the published range. That is a signal to double-check before you send it. Did you count ladder moves, travel and bad weather days? Is your crew really that fast? If your time log says yes, the price is right and you are a lean shop. If the market in your area is higher, you can charge it and keep the extra margin.

Break it into lines the customer can follow: siding, trim, doors, garage door, prep. Put your prep assumptions in writing ("scrape and sand about 300 sq ft of failing paint"), and say what happens if rot turns up once the paint comes off. A change order form makes that extra work easy to approve.

Example: the same house in the calculator

The paint estimate calculator has boxes for walls, ceilings, trim and doors. Outside, siding goes in walls, soffits and porch ceilings go in ceilings, and fascia, casing and corner boards go in trim. Prep, setup and the one-off items go in one prep box. Here is the house above typed into it, so you can check every number.

Inputs (Example):

BoxValue
Wall area / wall coats2,400 sq ft / 2 coats
Ceiling area0 (no soffit in this job)
Trim, base and casing / trim and door coats420 ft / 2 coats
Doors3 (the entry doors)
Wall paint coverage, per coat250 sq ft (the low end of Duration, for wood siding)
Trim coverage, per coat750 ft a gallon (Emerald's 350 to 400 sq ft a gallon on trim about 6 inches wide)
Doors per gallon, per coat10
Waste10%
Wall paint / trim and door paint, per gallon$55 / $60
Sundries for the job$592 (primer $80, caulk $112, masking and tips $120, detergent $30, lift and sprayer wear $250)
Walls, per coat400 sq ft/hr (spray and back-roll)
Trim, per coat30 ft/hr
Each door, per coat0.75 hours
Prep, setup and cleanup32.4 hours (wash 2.4, scrape 5, caulk and patch 12, mask 8, cleanup 3, and the garage door's 2)
Labor cost per crew hour$32.50
Overhead / target profit margin20% / 15%

What it shows:

ResultValue
Price$6,801.93
Labor hours76.9 (walls 12, trim 28, doors 4.5, prep 32.4)
Wall paint22 gal (needs 21.1)
Trim and door paint2 gal (needs 1.9)
Materials$1,922.00
Labor$2,499.25
Overhead$1,360.39
Job cost$5,781.64
Profit$1,020.29

That is the hand example to the cent: $4,421.25 of direct cost divided by 0.65. The calculator rounds up to the cent, so its $6,801.93 is the exact figure behind the hand example's rounded $6,802.

What moves the price

Change one input at a time in the calculator and watch the price. Each row below is the calculator example with one change, and every changed number comes from a cited range.

Change (Example)HoursSiding galPricePer sq ft
None76.922$6,801.93$2.83
One coat on siding70.911$5,571.16$2.32
Coverage 30076.918$6,463.47$2.69
Add soffit79.922$7,121.16$2.97
Trim at 20 ft/hr90.922$7,501.93$3.13
Brush and roll103.322$8,121.93$3.38
Trim at 15 ft/hr104.922$8,201.93$3.42

What each row changes: One coat on siding is a same-color repaint, which Duration's data sheet allows. Coverage 300 is the top of Duration's 250 to 300, for smooth siding. Add soffit puts 300 sq ft of soffit in the ceiling box, one coat at 100 sq ft/hr and 300 sq ft a gallon, at $55 a gallon. Brush and roll sets the siding to 125 sq ft/hr, the middle of CompositePaint's 100 to 150. Trim at 15 ft/hr is Fixr's slow end.

Two things stand out. Labor moves the price far more than paint does: better coverage saves $338, while slow trim adds $1,400 with no extra paint at all. And the rows at the example's fast pace land near the bottom of Fixr's $2.84 to $5.28 range, three of them just under it, while the slower rows sit well inside it. That is another sign the example's rates are on the fast side. Your own time log decides which row you are.

Common mistakes

  • Pricing by the floor plan. Measure the walls.
  • Treating prep as free. Washing, scraping, caulking and priming are hours. Write them in.
  • Underestimating trim. In the example, trim is 28 of 77 hours, more than a third.
  • Using the can's coverage on rough wood. Rough, bare or chalky wood needs more paint.
  • Skipping the lead check on older homes. Skipping the rule can mean serious penalties. Check the house's age before you quote.
  • Forgetting weather and cure time. Paint won't go on in rain or below the temperature limit on the data sheet. Build in weather days, and read the temperature, dew point and rain-after rules in Weather rules for exterior painting and staining.
  • No change-order line. Rotted fascia and boards turn up once the paint comes off. Say what you will charge to fix them.
  • Markup instead of margin. See the table in the deck guide, or Markup vs margin for contractors.

How Chalk helps

This part is about our software.

  • Price book. Add your siding, trim, door and prep lines to the price book with a unit (sq ft, lin ft, each, hour) and a price per unit, then build the quote from them. See Send a quote and get it approved, and Set up Chalk for a painting business for the items, job types and quote templates most painters start with.
  • Optional extras. Mark a second color or rotted-board repair as an Optional extra so the customer ticks what they want. Good, better, best pricing shows how to build options that lift the average job.
  • Cost view. The quote has a What the job will cost card, which the customer never sees. Owners, admins and sales roles see it by default; for anyone else it follows their role's Job prices and Pay on jobs and quotes settings.
  • Digital quote and invoice. Send the quote and invoice as links the customer can open on a phone, and ask for a deposit on the quote.

Looking for a quick number? Try the paint estimate calculator. Want a form to hand over? Use the painting estimate template.

FAQ

How much do painters charge per square foot for an exterior?

Fixr's national range is $2.84 to $5.28 per square foot of wall, with prep such as washing, caulking and masking included, and $2.15 to $3.99 per linear foot of trim. Walls in poor shape can cost over 60% more. Use those as a check only. The worked example on this page comes to $2.83 per square foot of wall from its own costs.

How many gallons of paint does it take to paint a house exterior?

Gallons are wall area times coats, divided by the coverage on the data sheet, plus about 10% for waste. Sherwin-Williams Duration lists 250 to 300 square feet a gallon, so 2,400 square feet of siding at two coats and 250 square feet a gallon needs 21.1 gallons with waste. You buy 22. Trim and doors take their own paint on top.

How long does it take to paint the outside of a house?

The example house on this page, 2,400 square feet of siding with 420 feet of trim and three doors, comes to 76.9 crew hours. Trim alone is 28 of them. Brushing and rolling the siding instead of spraying it pushes the total to 103.3 hours. Those are example rates. Time five of your own jobs.

Should I price trim separately from the siding?

Yes. Trim is counted in linear feet and goes far slower than siding. Fixr says 15 linear feet of trim takes 30 to 60 minutes. In the example on this page, slowing trim from 30 to 15 feet an hour raises the price from $6,801.93 to $8,201.93 without a single extra gallon of paint.

Does a one-coat repaint cost much less?

Less, but not half. Duration's data sheet allows one coat on a repaint and two on bare surfaces. In the example, going from two coats to one on the siding saves 6 hours and 11 gallons, and the price drops from $6,801.93 to $5,571.16, because the trim, doors and prep stay the same.

Do I need to follow the lead rule on an older house?

If the house was built before 1978 and your work disturbs more than 20 square feet of painted exterior surface, the EPA's Renovation, Repair and Painting rule applies, and your firm must be certified. Check the EPA's contractor page and your state's rules before you quote. This is not legal advice.

Sources

Prices and rates change and vary by region. Check the current version of each source.