Most deck stain quotes lose money in the same three places: the rails, the stairs and the prep. Boards are easy to measure and fast to coat. Everything else takes longer than the square footage says.
This guide gives you a method you can repeat on every deck: measure it in parts, choose a prep level, work out stain from the maker's data sheet, turn each part into hours, then turn cost into a price with overhead and profit built in. It has three worked examples, one of them run through the free deck and fence stain price calculator with every input shown, and ends with the mistakes that cost the most. Pricing a fence instead? Fences are measured by the linear foot and on both sides, so they have their own guide.
The method in six steps
- Measure the boards, the rails and the stairs as separate parts.
- Choose the prep level the wood needs: clean, strip, sand, repair.
- Work out stain from the data sheet's coverage, using the low end for rough or weathered wood.
- Turn each part into hours with production rates you have timed yourself.
- Add it up as cost, then price it so overhead and profit come out of the price, not on top of your cost.
- Check it against the market, then round it into price-book lines the customer can read.
What homeowners see online (and why it is not your price)
Your customer has probably read a cost guide. It helps to know what it says. Fixr's deck staining guide, last updated January 2025, gives these national ranges:
| What | Fixr's range |
|---|---|
| Stain a deck, including light sanding and sealing | $2 to $5 per sq ft |
| Labor / materials | $1.50 to $3 / $0.50 to $2 per sq ft |
| Handrails, posts and railings | $4 to $12 per linear foot |
| Stairs | $2 to $5 per sq ft |
| Add-on prep: cleaning / power washing | $0.25 to $0.50 / $0.30 to $0.40 per sq ft |
| Add-on prep: stripping / sanding | $1 to $3 / $1 to $4 per sq ft |
| Restoration / restaining | $4.50 to $6.50 / $4 to $7 per sq ft |
| Stain, per gallon | $25 to $80 |
| A 12 x 12 deck (144 sq ft) / 16 x 20 (320 sq ft) | $290 to $720 / $640 to $1,600 |
Those are averages across all kinds of providers in all kinds of places. Use them as a reality check after you have built your price, never to set it.
Step 1: Measure the deck in parts
A 240 sq ft deck with 48 feet of rail and four stairs is not a 240 sq ft job. Measure each part on its own, because each one takes a different amount of time.
| Part | How to measure | Price unit |
|---|---|---|
| Boards (the floor) | Length times width. Add landings, wrap-arounds and bump-outs as separate rectangles. | sq ft |
| Rails | Linear feet of top rail. Note the height, whether there are balusters, and how many posts and caps. | lin ft |
| Stairs | Count the treads. Note the width, open or closed risers, and the stringers. | each |
| Everything else | Skirt boards, bench seats, lattice, the underside of an upper deck. | lin ft, sq ft or each |
Photograph the deck and the wood from a couple of feet away. Note how high it sits off the ground, because a second-story deck means ladders or scaffold and that is time. Note the condition of the boards too: gray, mossy, splintered or already coated.
Step 2: Choose the prep level
Prep decides the price more than anything else. Write the level on the estimate, so the customer knows what they are buying.
| Level | When you need it | What you do |
|---|---|---|
| 1. Clean and brighten | Bare or weathered wood, or an old penetrating stain that has worn thin | Wash with a wood cleaner, rinse, brighten, let it dry |
| 2. Strip | An old film-forming stain or sealer that is peeling or fails the water test | Apply stripper, scrub and rinse, brighten, let it dry |
| 3. Sand | Mill glaze on new lumber, raised grain, rough or splintered boards | Sand after stripping or cleaning, then vacuum or blow off the dust |
| 4. Repair | Loose boards, popped screws, rot | Price by the hour or by the piece. Do not bury it in the stain price. |
What the makers and agencies say you must have before stain goes on:
- The wood has to take stain. Sherwin-Williams tells you to sprinkle water on the surface: if it soaks in quickly, it is ready; if it beads, remove the old coating and test again (SuperDeck data sheet). DEFY asks for the same few-seconds water test.
- New wood has to dry. DEFY's data sheet says to let new wood weather three to six months before staining (DEFY Extreme data sheet). The U.S. General Services Administration's stain procedure says not to apply when the wood's moisture content is above 12% or the relative humidity is above 85% (GSA).
- Weather matters. The SuperDeck sheet says to apply between 50 and 90 degrees F, not on a hot surface, and not if rain is expected within 24 hours. Other sheets add dew point, wood moisture and wait-after-washing rules. They are collected in Weather rules for exterior painting and staining.
- Watch the pressure. DEFY's sheet caps rinsing at 1,200 psi.
Step 3: Coats, coverage and product
Coverage on a can is a ceiling, not a promise. Rough, weathered and porous wood drinks more stain, so it covers less per gallon. These are numbers from data sheets and one government procedure:
| Source | Product type | Coverage per gallon | Coats |
|---|---|---|---|
| Sherwin-Williams SuperDeck oil-based semi-solid | Semi-solid oil | 150 to 400 sq ft, "depending on porosity and texture" | One. A second coat only wet on wet, and only what the wood absorbs. |
| Cabot Australian Timber Oil | Oil, semi-transparent | 250 to 600 sq ft | One coat only. Dries 24 to 48 hours. |
| Ready Seal technical data sheet | Oil, semi-transparent | 150 sq ft on a cedar or treated pine deck, 175 on a redwood deck, rated for new wood | One generous coat or two light coats, 45 minutes apart. Dries 48 to 72 hours. |
| DEFY Extreme | Water-based, semi-transparent | 100 to 150 sq ft with two coats | One coat on dense hardwoods, two on pressure-treated and other porous woods, about 20 minutes apart |
| GSA procedure | Semi-transparent oil, general | 200 to 400 sq ft on smooth wood, 100 to 200 on rough or weathered | Two on rough or weathered |
| Fixr | Homeowner average | 150 to 300 sq ft | Not stated |
Read the sheet for the product you will actually use, since coverage and coats differ a lot between brands.
How to turn that into gallons:
- Use surface area, not footprint. Boards are the footprint. For rails, start with length times height times two faces, then add for balusters. Stairs have treads, risers and stringers. Stain a test section and see what a gallon really does.
- Pick the coverage honestly. New, smooth boards can use the high end. Gray, rough or old boards use the low end.
- Add about 10% for waste, drips and touch-ups.
- More is not better. The SuperDeck sheet warns that excess stain that has not soaked in "must be removed to prevent adhesion issues" and a tacky finish. Spreading thinner on the second coat is cheaper and works better.
Gallons by deck size
Boards only, from the footprint. These are quick answers to "how many gallons of stain for a 12 by 12 deck?" Gallons = area x coats / coverage, plus 10% for waste. Rails, stairs and skirt boards add to it (see the next section and the worked example).
| Deck | Sq ft | One coat at 150 (rough or gray) | One coat at 250 | One coat at 350 (smooth, new) | Solid color, two coats at 250 each |
|---|---|---|---|---|---|
| 10 x 10 | 100 | 0.7 gal | 0.4 gal | 0.3 gal | 0.9 gal |
| 12 x 12 | 144 | 1.1 gal | 0.6 gal | 0.5 gal | 1.3 gal |
| 12 x 16 | 192 | 1.4 gal | 0.8 gal | 0.6 gal | 1.7 gal |
| 16 x 16 | 256 | 1.9 gal | 1.1 gal | 0.8 gal | 2.3 gal |
| 16 x 20 | 320 | 2.3 gal | 1.4 gal | 1.0 gal | 2.8 gal |
| 20 x 20 | 400 | 2.9 gal | 1.8 gal | 1.3 gal | 3.5 gal |
The one-coat columns follow the Sherwin-Williams SuperDeck semi-solid range of 150 to 400 sq ft per gallon. The solid-color column follows Cabot's solid-color acrylic stain data sheet, which lists 400 to 500 sq ft per gallon on smooth surfaces and 200 to 300 on rough ones, and requires two coats. A 12 by 12 deck of gray, rough boards in a semi-solid stain needs about 1.1 gallons, so two cans (or a gallon and a quart), and the same deck in solid color about 1.3. Round up to what you can buy.
Step 4: Production rates, the number that decides your margin
Here is the honest state of things. There is no free, current table of deck staining production rates from the stain makers or a trade group. What exists is software defaults and forum posts:
- One estimating program's default deck template uses a brushed first coat at 150 sq ft per hour and paint at 300 sq ft per gallon. Its example, a 300 sq ft deck plus 120 sq ft of rail with two brushed coats, comes out at 6.93 labor hours. That is about 60 sq ft of surface per labor hour across both coats.
- On a contractor forum, pros say that on small decks spraying and brushing take about the same time once masking, back-brushing, setup and cleanup are counted. On bigger decks one person sprays while a second back-brushes (Pressure Washing Resource thread). Nobody there gives a square-foot-per-hour figure.
So build your own. It takes five jobs. Until you have them, here are the rates this page uses. Every one is an example input, not a measured benchmark:
| Rate | Value on this page | Where it comes from |
|---|---|---|
| Wash prep | 300 sq ft/hr (calculator), 200 (12 by 12 example) | The calculator's starting default, and a made-up time log |
| Strip prep | 120 sq ft/hr (calculator and hand example) | The calculator's starting default |
| Sand prep | 60 sq ft/hr (calculator), 80 (12 by 12 example) | The calculator's starting default, and a made-up time log |
| Stain the floor, per coat | 150 sq ft/hr | The calculator's default, and the brushed first coat in the estimating program above |
| Stain railing, per coat | 12 ft/hr | The calculator's default |
| Stain stairs, per coat | 5 minutes a step (calculator), 15 minutes (hand examples) | The calculator's default, and a made-up time log |
| Setup, travel and cleanup | 1.5 hours | The calculator's default |
The hand examples run slower on stairs than the calculator does, on purpose: it shows how much one rate moves the price. Replace all of them with your own.
| Task | Quantity | Hours it took | Rate (quantity / hours) |
|---|---|---|---|
| Setup and masking | 1 job | ||
| Wash and brighten boards | sq ft | ||
| Wash and brighten rails | lin ft | ||
| Wash and brighten stairs | stairs | ||
| Stain boards | sq ft | ||
| Stain rails | lin ft | ||
| Stain stairs | stairs | ||
| Cleanup | 1 job |
Time each task on the next five decks and fill in the last column. Average them, then use your slower rates when you quote. You will see right away that rails and stairs run far slower than boards. Count the return trip too: if the boards need a day to dry before you coat the rails, that is another trip.
Step 5: From cost to price
Labor cost per hour is the wage plus the cost of having an employee. The Bureau of Labor Statistics puts median pay for construction and maintenance painters at $23.75 an hour as of May 2025, and it varies a lot by place. On top of wages the employer pays Social Security and Medicare tax (6.2% and 1.45%), workers' compensation and unemployment tax, which vary by state and class code. One estimating guide puts the total burden at 25% to 40% of wages. Work out yours from your own payroll.
Direct cost is labor, plus materials, plus job costs like fuel, dump fees or equipment you rent.
Price is direct cost divided by one minus overhead and profit, where both are a percentage of the price:
Price = direct cost / (1 - overhead % - profit %)
Overhead % is your yearly overhead (insurance, truck, phone, software, your own office time) divided by your yearly sales. For a benchmark, the National Association of Home Builders' remodeler survey for fiscal year 2024 found operating expenses averaged 23.6% of revenue, leaving a 6.3% net profit on average. That survey covers remodelers in general, and the operating expenses include the owner's pay. Painting-focused guides quote higher profit targets. One says small residential shops run 20% to 35% overhead and aim for 15% to 25% net.
Why divide instead of adding a markup? Because markup is a percentage of cost and margin is a percentage of price. Adding 30% to cost leaves you a 23% margin, not 30%. The full explanation is in Markup vs margin for contractors, and the markup and margin calculator converts one to the other.
| Markup on cost | Margin you actually keep |
|---|---|
| 25% | 20% |
| 50% | 33% |
| 100% (double your cost) | 50% |
The Painting Contractors Association tells new painters to charge double the job's cost, which is a 50% gross margin. That is a fair starting rule, as long as your costs include all your labor.
Example: a strip-and-stain deck, priced by hand
The job (Example): a 240 sq ft deck (15 by 16 ft), 48 ft of rail, 4 stairs. The boards are gray and a previous owner's film stain is flaking, so this is prep level 2 (strip and brighten). Water-based semi-transparent stain, two coats wet on wet.
Placeholders: labor costs $32.50 an hour (a $25 wage plus 30% burden). Overhead is 20% of price and profit is 15%. These are example numbers, not benchmarks.
Hours (rates are the placeholders from a made-up time log):
| Task | Quantity and rate | Hours |
|---|---|---|
| Setup, mask, move furniture | 1 job | 1.0 |
| Strip, wash, brighten boards | 240 sq ft at 120 sq ft/hr | 2.0 |
| Strip, wash, brighten rails | 48 ft at 24 ft/hr | 2.0 |
| Strip, wash, brighten stairs | 4 at 0.25 hr | 1.0 |
| Stain boards, two coats | 240 sq ft at 80 sq ft/hr | 3.0 |
| Stain rails, two coats | 48 ft at 12 ft/hr | 4.0 |
| Stain stairs, two coats | 4 at 0.5 hr | 2.0 |
| Cleanup | 1 job | 0.5 |
| Total | 15.5 |
Stain: surface area is 240 (boards) + 288 (48 ft x 3 ft high x 2 faces) + 40 (stairs) = 568 sq ft. At 125 sq ft per gallon for two coats (the middle of DEFY's range) that is 4.5 gallons, and about 5 with waste.
Materials:
| Item | Cost |
|---|---|
| Stain, 5 gal at $60 | $300 |
| Cleaner, stripper and brightener | $55 |
| Masking, brushes, pads, sandpaper | $45 |
| Total | $400 |
From cost to price:
| Item | Amount |
|---|---|
| Labor, 15.5 h x $32.50 | $503.75 |
| Materials | $400.00 |
| Direct cost | $903.75 |
| Price = $903.75 / (1 - 0.20 - 0.15) = $903.75 / 0.65 | $1,390 |
| Overhead share (20%) | $278 |
| Profit share (15%) | $208 |
Check it against the market. $1,390 over 240 sq ft is $5.79 per sq ft of deck, with the rails and stairs included. That is a little above Fixr's $2 to $5 for a standard staining job and inside its $4.50 to $6.50 for restoration. It makes sense for a strip-and-brighten with rails.
Round it into price-book lines by dividing each part's share of the cost back by its quantity:
| Line | Quantity | Unit price | Line total |
|---|---|---|---|
| Deck boards, strip and stain | 240 sq ft | $2.20 | $528 |
| Rails | 48 lin ft | $13.25 | $636 |
| Stairs | 4 each | $58.00 | $232 |
| Total | $1,396 |
The $6 over $1,390 is rounding. Rails come out near $13 a foot because they take 6 of the 14 hours of hands-on work. If that looks high next to Fixr's $4 to $12 a foot, remember that this example has balusters and a strip-and-brighten. Your time log will tell you whether yours do. When you hand it over, walk the customer through those lines and the prep level. How to present an estimate covers what to say.
Example: the same deck in the calculator
The deck and fence stain price calculator works a little differently from the hand example. It applies one prep rate to all of the stain area, rails and stairs included, and it times each coat of floor, rail and stairs from its own rate. Here is the same 240 sq ft deck typed into it, with every box shown, so you can check the math against the page yourself.
Inputs (Example):
| Box | Value |
|---|---|
| Deck floor area | 240 sq ft |
| Railing | 48 ft |
| Stair steps / stair width | 4 steps / 4 ft |
| Fence length | 0 |
| Coverage per gallon, per coat | 250 sq ft (two coats at 250 is the middle of DEFY's 100 to 150 sq ft a gallon for two coats) |
| Waste and overspray | 10% |
| Railing surface per linear foot | 6 sq ft (the rail check in Railings) |
| Other materials for the job | $55 (cleaner, stripper, brightener, tape) |
| Production rates | Wash 300, strip 120, sand 60 sq ft/hr. Floor 150 sq ft/hr, railing 12 ft/hr, stairs 5 minutes a step, all per coat. Setup, travel and cleanup 1.5 hours. |
| Labor cost per crew hour | $32.50 |
| Overhead / target profit margin | 20% / 15% |
| Good | Wash only, 1 coat, stain at $40 a gallon |
| Better | Strip, 2 coats, stain at $60 a gallon |
| Best | Sand, 2 coats, stain at $70 a gallon |
The calculator counts stairs at 1.5 sq ft per foot of width per step (tread and riser), so the stain area is 240 + 288 (48 ft x 6) + 24 (4 x 4 x 1.5) = 552 sq ft.
What it shows:
| Good | Better | Best | |
|---|---|---|---|
| Price | $734.24 | $1,446.16 | $1,753.09 |
| Gallons to buy | 3 (needs 2.4) | 5 (needs 4.9) | 5 (needs 4.9) |
| Labor hours | 9.3 | 18 | 22.6 |
| Materials | $175.00 | $355.00 | $405.00 |
| Labor | $302.25 | $585.00 | $734.50 |
| Overhead | $146.85 | $289.23 | $350.62 |
| Job cost | $624.10 | $1,229.23 | $1,490.12 |
| Profit | $110.14 | $216.93 | $262.97 |
How the Better hours add up: strip 552 / 120 = 4.6 hours. One coat is 240 / 150 = 1.6 hours of floor, 48 / 12 = 4 of rail and 4 x 5 minutes = 0.33 of stairs, so 5.93 hours, and two coats are 11.87. With 1.5 hours of setup that is 17.97, rounded to 18.0. Labor is 18 x $32.50 = $585. Materials are 5 gallons x $60 + $55 = $355. The price is ($585 + $355) / (1 - 0.20 - 0.15) = $940 / 0.65 = $1,446.16, and the calculator rounds up to the cent so the margin never lands a hair under 15%.
The Better price is $56 above the hand example's $1,390 for the same strip-and-stain. Most of the gap is prep: the calculator strips all 552 sq ft at one rate, where the hand example timed the rails and stairs on their own. Neither is wrong. Pick the method that matches how your crew really works, then check it against five real jobs. Showing all three prices side by side is the idea behind good, better, best pricing.
Railings
Railings are the part of a deck quote that gets underpriced most often. A 4-foot-by-3-foot section of boards takes minutes to coat. The same footprint in rail, with balusters, takes much longer. Fixr's range is $4 to $12 per linear foot of handrail, posts and railing, which is wide because the styles are so different.
Measure the linear feet of top rail, count the posts and caps, note the height, and write down the style: balusters, cable, metal or glass infill, lattice. Photograph a section up close.
Surface per foot. The "length x height x two faces" rule in the worked example gives 6 sq ft of surface per linear foot for a 3-foot rail. You can check it with geometry. Say the balusters are 2 by 2 (1.5 inches actual) and spaced about 5 inches apart, centre to centre, which leaves a gap of 3.5 inches. That is 2.4 balusters per foot of rail. Each 32-inch baluster has four faces, so 4 x 1.5 x 32 = 192 square inches, or 1.33 sq ft. That is 3.2 sq ft per foot of rail from balusters alone, plus the top cap and bottom rail, for roughly 5 sq ft per foot. So 6 sq ft is a safe figure for stain. These dimensions are assumptions, so measure your own.
Time. The surface area is not the problem. Each baluster has four faces and edges, and a brush or pad has to reach each one. In the worked example the rail takes 4.0 of 15.5 hours to stain and 2.0 more to prepare, and it comes out at $13.25 a foot. Price each style from a rate you have timed. A top rail with cable or glass infill is far less work per foot than a rail with balusters. Do not use one rail price for every deck.
Rules that keep rails profitable:
- Price rail by the linear foot, not as a share of the deck.
- Charge extra for balusters, or set separate rates by style.
- Price posts, caps and newel posts each.
- Set a minimum, because a 10-foot run still means setup and cleanup.
- Remember rails are often painted or already coated. Test the prep.
A 12 by 12 deck: wash and stain, or sand and stain
Small decks fool people. A 12 by 12 deck is only 144 sq ft of boards, but if it has 24 feet of rail and three stairs, more than half of the hours go to the rail and stairs. This section prices the same deck two ways, using the same placeholders as the worked example: labor at $32.50 an hour, overhead 20%, profit 15%, water-based semi-transparent stain at two coats wet on wet (125 sq ft per gallon), and stain at $60 a gallon.
The deck: 144 sq ft of boards, 24 ft of rail, 3 stairs. The wood is sound and gray, with an old penetrating stain that has worn thin. That is prep level 1 (clean and brighten) for the first option, and level 3 (sand) for the second, for a customer who wants the smoothest finish.
Stain area: 144 sq ft of boards, 144 sq ft of rail (24 x 3 x 2) and about 20 sq ft of stairs is 308 sq ft, which is 2.5 gallons and 3 with waste.
Wash and stain
| Task | Quantity and rate | Hours |
|---|---|---|
| Setup and masking | 1 job | 1.00 |
| Wash and brighten boards | 144 sq ft at 200 sq ft/hr | 0.72 |
| Wash and brighten rails | 24 ft at 40 ft/hr | 0.60 |
| Wash and brighten stairs | 3 at 0.15 hr | 0.45 |
| Stain boards, two coats | 144 sq ft at 80 sq ft/hr | 1.80 |
| Stain rails, two coats | 24 ft at 12 ft/hr | 2.00 |
| Stain stairs, two coats | 3 at 0.5 hr | 1.50 |
| Cleanup | 1 job | 0.50 |
| Total | 8.57 |
| Item | Amount |
|---|---|
| Labor, 8.57 h x $32.50 | $278.53 |
| Stain, 3 gal at $60 | $180.00 |
| Cleaner and brightener | $35.00 |
| Masking and supplies | $30.00 |
| Direct cost | $523.53 |
| Price = $523.53 / 0.65 | $805 |
| Overhead share (20%) | $161 |
| Profit share (15%) | $121 |
That is $5.59 per sq ft of deck. Fixr's standard staining range is $2 to $5 per sq ft and its restoration range is $4.50 to $6.50, so it sits in the restoration range.
Sand and stain
Add sanding to the same job: boards at 80 sq ft per hour (1.80), rails at 12 ft per hour (2.00) and stairs at 0.4 hour each (1.20), plus $45 of sandpaper and discs.
| Item | Amount |
|---|---|
| Hours: 8.57 + 5.00 | 13.57 |
| Labor, 13.57 h x $32.50 | $441.03 |
| Materials: $245 + $45 | $290.00 |
| Direct cost | $731.03 |
| Price = $731.03 / 0.65 | $1,125 |
| Overhead share (20%) | $225 |
| Profit share (15%) | $169 |
That is $7.81 per sq ft of deck, and the sanding adds $320 to the price. Fixr lists sanding at $1 to $4 per sq ft as an add-on, which on 144 sq ft of boards is $144 to $576. Its restoration range tops out at $6.50, so this price is above it. The reason is the rail and stairs, which are sanded at a slow pace in this example. Show the customer both prices side by side. Many will choose the wash and stain once they see $320 for the difference, and some will choose the sanding because they want the smooth finish.
Neither price includes repairs. Loose boards and popped screws are hourly extras.
Good, better, best
Once you know your cost for each part, offering three levels is easy. The difference is mostly prep and product: a clean-and-brighten with a one-coat penetrating stain, a strip-and-brighten with a two-coat semi-transparent, and a full sand with a longer-lasting product. Price all three from the same math, the way the calculator example does. Do not discount the top one to make the middle one look good.
Common mistakes
- Pricing by deck size only. Rails and stairs are the time sink. Price them as their own lines.
- Using the best-case coverage on the can. Gray, rough wood will not cover like new smooth wood.
- Quoting prep you cannot see. Put the prep level in writing and add a line for extra stripping or repairs at an hourly rate.
- Forgetting the waiting. Dry times and a second trip are job costs even when you are not on site.
- Pricing off a homeowner cost guide. Those are averages across everyone. Your own costs set the floor.
- Adding markup when you meant margin. See the table above.
- Skipping the expectations talk. Gray boards, color variation and weather delays cause most callbacks. A written expectations and waiver form heads them off.
- Never recording actual hours. Your production rates are only as good as your last five jobs.
How Chalk helps
This part is about our software. Skip it if you only want the pricing math.
- Price book. Put your deck lines in the price book with a unit (sq ft, lin ft, each, hour) and a price per unit, then pick them when you build a quote. See Send a quote and get it approved, and Set up Chalk for deck and fence staining for the items most staining shops start with.
- One line, several measurements. Under Settings > Company there is a switch called Measure work several ways on one line. It is off until you turn it on. With it on, a deck can be priced from its boards, its rails and its stairs at once. The customer sees one line and one price. You see the detail. If you fill in what each item uses, the quote also shows a What to buy list. Price one line several ways walks through the setup.
- A cost view. The quote has a What the job will cost card, which the customer never sees. Owners, admins and sales roles see it by default; for anyone else it follows their role's Job prices and Pay on jobs and quotes settings. It lists materials, crew pay and the overhead percent you set, and shows what is left before profit splits.
- Quote and invoice online. Send the quote as a link the customer can approve on their phone, with optional extras and a deposit. Send the invoice the same way.
Need only a quick number? Try the deck and fence stain price calculator. Want a form to hand over? Use the free deck and fence staining estimate template.
FAQ
How much should I charge per square foot to stain a deck?
Fixr's national range is $2 to $5 per square foot for a standard stain job with light sanding, and $4.50 to $6.50 for restoration. Build your own price from your costs first. In the examples on this page the price works out to $3.06 to $7.81 per square foot of deck floor, because the rails and stairs are priced into the floor number.
How many gallons of stain do I need for a 12 by 12 deck?
The boards are 144 square feet. One coat on rough or gray boards at 150 square feet a gallon needs about 1.1 gallons with 10% waste. Smooth new boards at 350 square feet a gallon need about half a gallon. Rails and stairs add to that, so measure them too and check the gallons by deck size table.
Should I price deck railings separately from the floor?
Yes. Price rails by the linear foot, and price posts and caps each. Rails are slow, detailed work. Fixr lists $4 to $12 per linear foot for handrails, posts and railings, and in this guide's strip-and-stain example the rail comes to $13.25 a foot because it has balusters.
How many hours does it take to stain a deck?
It depends on the prep, the coats and the rails. In the calculator example on this page, a 240 square foot deck with 48 feet of rail and 4 stairs takes 9.3 hours for a wash and one coat, and 22.6 hours for a sand and two coats. Those rates are example inputs. Time your own crew on five decks and use your slower average.
How much more should I charge to strip or sand a deck?
Fixr lists stripping at $1 to $3 and sanding at $1 to $4 per square foot as add-ons. Price it from your own hours instead. In the 12 by 12 example on this page, sanding adds $320 to an $805 wash and stain, mostly because the rail and stairs sand slowly.
Can you stain new pressure-treated wood right away?
Usually not. DEFY's data sheet says to let new wood weather three to six months, and Ready Seal's says wood must be at 12% moisture or less. Do the water test: if drops soak in within a few seconds, the wood will take stain. If they bead, wait or prep the surface.
Sources
Prices, rates and coverage change and vary by region. Check the current version of each source.
- Fixr: cost to stain a deck, updated January 31, 2025.
- Sherwin-Williams SuperDeck Oil-Based Semi-Solid Wood Stain, product data sheet, March 2025.
- Cabot Australian Timber Oil product page.
- Cabot Solid Color Acrylic Stain + Sealer #1800 Series, technical data, for solid-color coverage.
- DEFY Extreme Wood Stain product data sheet, SaverSystems, 2020.
- Ready Seal Stain and Sealer technical data sheet, for coverage by wood type and the 12% moisture rule.
- U.S. General Services Administration: Applying a semi-transparent or opaque stain to wood, archived copy (the gsa.gov page no longer loads).
- Pressure Washing Resource forum thread on applying deck stain. Contractor posts, used as color only.
- U.S. Bureau of Labor Statistics: painters, construction and maintenance.
- IRS: Topic no. 751, Social Security and Medicare withholding rates.
- NAHB Eye on Housing: remodelers saw profit margin gains in 2024.
- CompositePaint: how to estimate a paint job, an estimating guide used for labor burden and overhead ranges.
- Painting Contractors Association: the number one mistake new painting contractors make, archived copy (the pcapainted.org page no longer loads).
- EPA: Renovation, Repair and Painting Program for contractors.