Most deck staining arguments are not about the work. They are about surprises: "Why are some boards darker?" "Why is the old gray still showing?" "Why did it peel where the old finish was?" "Why did you push my job back?"
This form puts the answers in writing before you start. It explains in plain words what staining can and cannot do, and it asks the customer to sign that they understand.
How to use it
- Give it before you start, ideally with the estimate, so the customer has time to read it and ask questions. Not on the morning of the job.
- Fill in the brackets. Your business name, prep level, product, weather rule, warranty and recoat advice. Delete anything that is not true for how you work.
- Match it to the product. Weather limits, dry times and recoat advice come from the product's data sheet. Look up yours.
- Take photos. Photograph the deck before you start (gray boards, old finish, cracks) and keep them with the signed form.
- Keep a signed copy. Give one to the customer and keep one with the job.
- Do not use it to excuse bad work. The form explains the limits of the material. It does not replace doing the work properly.
The form
Deck staining: what to expect
| Field | Answer |
|---|---|
| Customer | |
| Property address | |
| Contractor | [Your business name] |
| Estimate number and date |
Please read this before we start. It explains what staining can and cannot do. If anything is unclear, ask us before you sign.
1. Wood is a natural material, and color varies. Every board is a little different. Wood species, age, density, grain, moisture and past treatments all change how a board takes stain. The color on a sample, a color chip or a photo is a guide, not a promise. Stain makers say the same in their data sheets: wood species, texture and natural color all affect the finished shade. Expect some board-to-board variation, including darker end grain and lighter or darker patches. We recommend a test area before the full job, and we will do one if you ask.
2. Gray, weathered and aged wood. Unfinished wood left outdoors changes color and roughens as it weathers. Cleaning and brightening can bring back much of the color, but cannot make old wood look new. Cracks, splits, checking, cupping, raised grain, rust stains and sap or tannin stains may remain after cleaning and staining, and staining does not repair them. If we find boards that need repair or replacement, we will tell you and you can decide.
3. Preparation.
We will prepare the deck as follows (check):
☐ Clean and brighten
☐ Strip old finish
☐ Sand
☐ Repairs (list them):
Some old finish may be impossible to remove completely, particularly in cracks, edges and around fasteners. Areas where old finish remains may look different once stained.
4. Adhesion and old finishes. Stain has to soak into bare, clean, dry wood to last. If the deck has an old film-forming stain, sealer or paint that we cannot fully remove, if the wood is wet or still has mill glaze, or if the wood is new pressure-treated lumber that has not dried, stain may not bond, and it may peel, flake, look blotchy or wear sooner in those areas. [We do not warrant adhesion over old finishes or over wood that is not ready for stain.] We will tell you if we see a risk. If you want us to go ahead anyway, we do so at your direction and understanding of the risk.
5. Weather and scheduling. Stain needs dry weather and moderate temperatures. The product we plan to use, [product name], is to be applied between [temperature range from the data sheet] and not if rain is expected within [number] hours. We may reschedule for rain, wind, heat, cold, or wet wood. We will tell you before we move the date, and weather delays are [not charged / charged at your rate]. Dates are estimates.
6. After we finish. Keep off the deck, and keep pets, furniture and grills off it, for [time from the data sheet, for example 24 hours] after the last coat. Full cure can take longer in cool or humid weather. Wet leaves, planters, rubber mats and furniture feet can trap moisture and mark the finish. Foot traffic, sun and rain wear the finish fastest on stairs, rails and boards in full sun.
7. How long it lasts. No stain lasts forever. How long it lasts depends on the product, the wood, the number of coats, and how much sun and rain the deck gets. [Adjust to your product.] The U.S. General Services Administration's guidance for semi-transparent oil-based stain says a single coat on smooth wood should last about 2 to 4 years, and a two-coat system up to about 8 years depending on exposure. Expect to clean and recoat on a regular schedule. We recommend: [your advice, for example inspect each spring and recoat every 2 to 3 years].
8. Property and plants. We take care to protect plants, siding, masonry and nearby surfaces. Cleaners and stain can still mark porous surfaces or harm plants. Please tell us before we start about anything fragile or valuable. Please make sure we can reach water and power, that sprinklers are off, and that cars are moved if needed.
9. Our workmanship. [Write what you will honor and for how long. For example, "We will return to fix any area we missed or applied incorrectly within 30 days of completion." Leave this blank if you do not offer one.]
10. Acknowledgment. I have read this form, I understand the points above, and I have had the chance to ask questions. I understand the color and finish will vary from samples, that old finishes and wood condition limit what staining can do, that weather may change the schedule, and that the finish will need maintenance.
| Field | Answer |
|---|---|
| Customer signature | |
| Printed name | |
| Date | |
| Contractor signature | |
| Date |
Where the wording comes from
The form's statements about color, weathering, temperature, dry time and expected life come from the sources below. Check the data sheet for your own product, because limits differ between brands.
- Color and species. Sherwin-Williams SuperDeck data sheet says wood species, textures and natural color all affect the finished shade, and to test a small area first.
- Weathering. The U.S. Forest Products Laboratory's Wood Handbook chapter on finishing says unfinished wood surfaces exposed to the weather change color and are roughened by photodegradation and surface checking.
- Adhesion and old finishes. The same SuperDeck sheet says not to apply over sealed or previously coated surfaces, and tells you to test by sprinkling water on the surface. DEFY's data sheet says surfaces must be clean, porous and dry, and that new wood should weather for three to six months before staining.
- Weather. SuperDeck's sheet says to apply between 50 and 90 degrees F, not on a hot surface, and not if rain is likely within 24 hours. The General Services Administration's stain procedure says not to apply above 85% relative humidity or 12% wood moisture content.
- How long it lasts. The same GSA procedure: a single coat on smooth wood should last 2 to 4 years, and a two-coat system up to 8 years, depending on exposure.
- Dry time. SuperDeck lists touch dry in 8 hours and ready to use in 24 to 48 hours. DEFY says allow 24 hours for the deck to cure completely.
Tips
- Talk it through. Go through the form with the customer on site. People remember what you said out loud.
- Keep it short for small jobs. For a front step or a bench, cut it down to the points that matter.
- Update it when you change products. Dry times, weather limits and coat counts change by product.
- Add a written warranty. See the workmanship warranty template.
- Pair it with a written estimate. The estimate template lists the scope, the prep level and the price. See the pricing guide for how to build that price.
Using Chalk instead of paper
If you would rather send this digitally, Chalk can send estimates and invoices as links the customer opens on their phone, and a quote can carry your terms. See Send a quote and get it approved for the steps. A paper copy works too, and this form does not need Chalk.