The most common mistake in an exterior paint estimate is measuring the wrong thing. Floor area tells you what a house costs to heat. It tells you very little about how much siding there is to paint, because the siding depends on the perimeter, the height, the roof shape and how many windows and doors cut holes in it. Two houses with the same floor area can differ by 40% in paintable wall.
This guide shows a walk-around order you can do in 20 minutes with a tape, the formulas for walls, gables and trim, whether to subtract openings, how far a floor-area shortcut can be trusted, and tables of gallons for houses from 1,200 to 3,000 square feet. It ends with a field sheet you can copy and a worked example.
The walk-around order
A fixed order stops you from missing a wall or measuring one twice.
- Start at the front door, facing the house. Sketch the footprint on a sheet of paper: a rough rectangle or the actual shape.
- Work clockwise, one elevation (wall) at a time. Label them front, right, back, left.
- For each elevation, record: length, height to the soffit, whether there is a gable above it, and everything on it (windows, doors, vents, garage door, bump-outs).
- Measure the trim as you go: window and door casing, corner boards, fascia, rakes, soffit.
- Count the extras: shutters, railings, porch posts, columns, a deck, a detached garage.
- Photograph each elevation straight on, and note what changes the price (rotted boards, peeling, bare wood, masonry, aluminum, steep ground, shrubs against the wall).
A 100-foot tape and a laser measure make it quick. Measure the height of one story once, and use it for every wall of the same level.
Walls and gables
Walls are rectangles:
Wall area = length x height
For a house with no bumps, add up the perimeter and multiply by the wall height:
Walls = perimeter x height x stories
Use the height from the foundation (or the bottom of the siding) to the soffit. On a two-story house that is the sum of both stories and the rim between them, usually around 18 to 20 feet. A tape on a pole or a laser measure from a safe spot gets it.
Gables are triangles on the end walls under the roof peak:
Gable area = base x height / 2
The base is the width of the wall at the eave line. The height is the rise from the eave to the peak, which you get from the roof pitch: rise = (base / 2) x (pitch / 12). For a 6 in 12 roof, the rise is a quarter of the base. A 26-foot-wide gable at 6 in 12 has a rise of 6.5 feet and an area of 26 x 6.5 / 2 = 84.5 sq ft. Add each gable to the walls.
Complex shapes. Break them into rectangles and triangles. A bump-out, a dormer, a porch wall and a bay each have their own area. Add them to the total.
Openings: subtract or not
Windows and doors are holes in the wall, and you do not paint them. Whether you subtract them is a policy choice. The rule in at least one estimating guide is to deduct only openings larger than about 50 square feet, because small openings cost you time to cut around. Pick a rule and use it on every job.
Here is what the choice does on the worked example below (a 2,000-ish sq ft two-story house):
| Policy | Paintable wall | Gallons, one coat at 300 | Gallons, two coats at 250 |
|---|---|---|---|
| Subtract every opening | 2,049 sq ft | 8 | 19 |
| Subtract only openings over 50 sq ft (the garage door) | 2,361 sq ft | 9 | 21 |
The difference is 312 sq ft, one to two gallons. The difference in labor is bigger, because cutting in around 18 windows takes time that the square footage does not count. That is why many painters subtract nothing for small openings and price the cut-in on the trim.
Count the openings anyway. You need them for trim, and you need them to price the work.
Trim, soffit and fascia by the foot
Trim is priced by the linear foot, because that is how the time behaves. See How to price exterior painting for rates.
| Part | How to measure |
|---|---|
| Window casing | 2 x (width + height) per window, plus the sill. A 3 by 5 ft window is 16 feet. |
| Door casing | 2 x height + width per door. A 3 by 7 ft door is 17 feet. |
| Corner boards | Wall height x number of corners (a simple rectangle has 4) |
| Fascia | Eave length on each side |
| Rakes (the sloped edges of a gable) | Hypotenuse of the gable: the square root of (half the base squared plus the rise squared), per side |
| Soffit | Eave length x overhang, in square feet, if you are painting it |
| Garage door, entry doors, shutters | Count each. Measure doors that have panels. |
| Railings, columns, posts | Count or measure each |
From floor area to wall area: the quick factor, and when it lies
Everyone asks: "how much paint for a 2,000 sq ft house?" You can answer in a minute with a factor, as long as you know what it assumes. The walls-to-floor ratio is not a constant. It falls as the house gets bigger, because floor area grows with the square of the dimensions and wall area grows with the dimensions.
This table uses a simple rectangle 1.5 times as long as it is wide, 9 feet of wall per story, a 6 in 12 gable roof with the gables on the narrow ends, and no openings subtracted:
| Floor area | One story: wall area / floor area | Two story: wall area / floor area |
|---|---|---|
| 1,200 sq ft | 1.23 | 1.58 |
| 1,500 sq ft | 1.12 | 1.42 |
| 1,800 sq ft | 1.03 | 1.31 |
| 2,000 sq ft | 0.99 | 1.25 |
| 2,500 sq ft | 0.90 | 1.12 |
| 3,000 sq ft | 0.84 | 1.03 |
So a rough "walls are about the same as the floor area" works for a 2,000 sq ft ranch and is wrong for a 1,200 sq ft two-story. And it lies for any house that is not a plain rectangle. A long thin house, an L-shape, a house with a tall foyer, a walkout basement, a lot of dormers or a three-car garage will be far off. The quick factor is for a phone call. It is not for a quote.
Gallons by house size
These tables take the wall area from the same assumptions (rectangle 1.5 to 1, 9 feet per story, 6 in 12 gables on the narrow ends), take off 10% for windows and doors (a rule of thumb; replace it with your count), then work out gallons from coverage and add 10% for waste.
The two coverage cases come from the Sherwin-Williams Duration data sheet, which lists 250 to 300 sq ft per gallon and says to apply one coat on a repaint and two coats on bare surfaces:
- One coat, repaint, smooth siding: 300 sq ft per gallon.
- Two coats, new or bare siding, or a color change: 250 sq ft per gallon per coat.
| Floor area | Stories | Gross wall area | After 10% for openings | Gallons, one coat | Gallons, two coats |
|---|---|---|---|---|---|
| 1,200 sq ft | 1 | 1,473 | 1,326 | 5 | 12 |
| 1,200 sq ft | 2 | 1,900 | 1,710 | 7 | 16 |
| 1,500 sq ft | 1 | 1,673 | 1,506 | 6 | 14 |
| 1,500 sq ft | 2 | 2,137 | 1,924 | 8 | 17 |
| 1,800 sq ft | 1 | 1,859 | 1,673 | 7 | 15 |
| 1,800 sq ft | 2 | 2,355 | 2,119 | 8 | 19 |
| 2,000 sq ft | 1 | 1,977 | 1,779 | 7 | 16 |
| 2,000 sq ft | 2 | 2,490 | 2,241 | 9 | 20 |
| 2,200 sq ft | 1 | 2,090 | 1,881 | 7 | 17 |
| 2,200 sq ft | 2 | 2,621 | 2,358 | 9 | 21 |
| 2,500 sq ft | 1 | 2,254 | 2,028 | 8 | 18 |
| 2,500 sq ft | 2 | 2,806 | 2,526 | 10 | 23 |
| 3,000 sq ft | 1 | 2,512 | 2,261 | 9 | 20 |
| 3,000 sq ft | 2 | 3,096 | 2,786 | 11 | 25 |
Short answers. For a 2,000 sq ft house exterior: about 7 to 9 gallons for one coat of siding paint, and 16 to 20 gallons for two. For 1,500 sq ft: about 6 to 8 gallons, or 14 to 17 for two coats. For 3,000 sq ft: about 9 to 11, or 20 to 25 for two coats.
What these leave out:
- Trim, doors, soffit, fascia and the garage door. Those use a different paint (often a trim enamel at a different coverage). Sherwin-Williams' Emerald Urethane Trim Enamel data sheet lists 350 to 400 sq ft per gallon, so count the trim separately.
- Primer on bare spots.
- Rough surfaces. Stucco, rough wood, brick and masonry soak up more paint. Use the low end of the coverage range, or lower.
- Dark-to-light color changes, which often need a tinted primer and two finish coats.
- Spray waste. Spraying loses more to the air than rolling does.
For a quick interactive version, the paint estimate calculator lets you put in your own numbers.
A worked example
The house: a two-story with a 26 by 38 ft footprint (1,976 sq ft of floor), a 6 in 12 gable roof with gables on the 26 ft ends, 9 feet per story, 18 windows (each 3 by 5), two entry doors (3 by 7) and a 16 by 7 foot garage door. Siding is painted wood.
| Item | Working | Area or length |
|---|---|---|
| Perimeter | 2 x (26 + 38) | 128 ft |
| Walls | 128 x 18 | 2,304 sq ft |
| Gables | 2 x (26 x 6.5 / 2) | 169 sq ft |
| Gross wall area | 2,473 sq ft | |
| Windows | 18 x 15 | 270 sq ft |
| Entry doors | 2 x 21 | 42 sq ft |
| Garage door | 16 x 7 | 112 sq ft |
| Openings total | 424 sq ft | |
| Paintable wall, all openings out | 2,473 - 424 | 2,049 sq ft |
| Paintable wall, only the garage door out | 2,473 - 112 | 2,361 sq ft |
| Trim | Working | Length |
|---|---|---|
| Window casing | 18 x 16 | 288 ft |
| Door casing | 2 x 17 | 34 ft |
| Corner boards | 4 x 18 | 72 ft |
| Fascia (eaves) | 2 x 38 | 76 ft |
| Rakes | 4 x 14.5 | 58 ft |
| Trim total | 528 ft |
Paint: with all openings out, one coat at 300 sq ft per gallon is 2,049 / 300 = 6.8 gallons, or 7.5 with 10% waste, so 8 gallons. Two coats at 250 is 2,049 x 2 / 250 = 16.4 gallons, or 18.0 with 10% waste, so buy 19. Count the garage door, entry doors and trim paint separately.
That 2,049 sq ft is the number to carry into How to price exterior painting: the siding line is wall area, and the trim line is 528 feet.
A field sheet
Copy this onto paper or a note on your phone.
| Elevation | Length | Height | Gable base / rise | Windows (count, size) | Doors | Notes |
|---|---|---|---|---|---|---|
| Front | ||||||
| Right | ||||||
| Back | ||||||
| Left | ||||||
| Bump-outs, dormers |
| Trim and extras | Count or feet |
|---|---|
| Window casing, total feet | |
| Door casing, total feet | |
| Corner boards, total feet | |
| Fascia and rakes, total feet | |
| Soffit, sq ft | |
| Garage doors, entry doors | |
| Shutters, railings, posts |
| Conditions | Yes / no / how many sq ft |
|---|---|
| Peeling or bare wood | |
| Rot to repair | |
| Masonry, stucco or aluminum | |
| Built before 1978 (lead rule) | |
| Color change dark to light | |
| Second story or steep ground | |
| Shrubs against the wall |
Mistakes to avoid
- Using the floor-plan square footage.
- Measuring only the front. Walk all four sides.
- Forgetting the gables. They are 100 to 500 sq ft on a house like these.
- Not recording the height and the number of stories.
- Subtracting openings one way on one quote and another way on the next.
- Treating trim as part of the wall. It is a different material, a different method and a different price.
- Using the quick factor on an L-shaped house.
- Skipping the photos and notes. You will need them when the customer asks why the price changed.
How Chalk helps
This part is about our software.
- One line, several measurements. Under Settings > Company there is a switch called Measure work several ways on one line. It is off until you turn it on. With it on, a price-book item can be priced from several counts, such as siding in square feet and trim in linear feet, plus doors by the each. You type the counts from your field sheet, and the customer sees one line and one price (you can show them the counts too, under Settings > Documents).
- Price book. Put your siding, trim and door lines in the price book with a unit (sq ft, lin ft, each), then pick them on a quote. See Send a quote and get it approved.
- What to buy. If you tell the price book what each item uses, the quote shows a What to buy list.
- Photos. Upload Before photos of each elevation to the job from your phone.
For a form to take on site, use the painting estimate template.
Sources
Coverage and rates change and vary by product. Check the current version of each source.
- Sherwin-Williams Duration Exterior Acrylic Flat, product data sheet, for coverage and coats.
- Sherwin-Williams Emerald Urethane Trim Enamel, product data sheet, for trim coverage.
- CompositePaint: how to estimate a paint job. An estimating guide; its rule on deducting openings is used as one example of a policy.