Sealing is the natural next step after a wash. The surface is clean, the customer can see the difference, and a sealer keeps it that way. It is also a job where the product matters more than in almost any other trade: a film-forming sealer, a penetrating one and an acrylic concrete sealer have different coverage, different coats, different dry times and different failure modes. The price follows the product.
This guide shows how to price paver and concrete sealing per square foot, what the sealer data sheets say about coverage, coats and conditions, how to price cleaning and joint sand, how long the job takes, and how to sell sealing as an upsell to a wash. It ends with a worked example for a 600 sq ft paver patio.
Who does it
Pressure washers and soft washers are the most common sealers, because they already clean the surface. Hardscape installers seal their own work. Painters and stainers who do decks and fences add it as a related finish. If you already wash patios and driveways, see the pressure washing pricing guide and the pressure washing price calculator.
What homeowners see online
Concrete sealing has published prices. Paver sealing mostly does not, so be careful about what a "per square foot" figure includes.
| Source | What it says |
|---|---|
| HomeAdvisor (updated June 2026) | Professional concrete sealing $1.35 to $2.50 per sq ft. By area: 100 sq ft $135 to $250, 500 sq ft $675 to $1,250, 1,000 sq ft $1,350 to $2,500. Sealer by the gallon: acrylic $16 to $75, polyurethane $25 to $110, epoxy $40 to $175 |
| Bob Vila (updated February 2023) | Sealing only, professional labor, $1.25 to $1.75 per sq ft. Cleaning and sealing $1.20 to $1.75 |
Both are about concrete, not pavers. Pavers have joints, sand, edges, efflorescence and more cleaning, so expect paver work to cost more per square foot. A short patio also feels the minimum charge more than a long driveway does.
Measure and inspect
- Area. Length x width of each section, minus planters and anything you will not seal.
- Type. Concrete pavers, clay brick, natural stone, stamped concrete, a plain slab. They behave differently.
- Age and history. New pavers are not ready for sealer for weeks (see below). An older patio may already have a sealer on it, and mixing sealers fails. SRW's data sheet says not to use more than one sealer on the same project.
- Joints. Are they full? Is the sand washed out? Are there weeds or ant mounds?
- Stains and efflorescence. Oil, rust, white mineral haze, tannin from leaves.
- Slope and use. A driveway takes tire marks and drips. A pool deck needs slip resistance.
- Plants and edges that need protecting from sealer.
Take photos in raking light. A paver patio looks different after sealing, and you want to show what it looked like before.
Clean and sand the joints
Prep is more than half of a paver seal.
- Wash. Remove dirt, algae and stains. Sealers lock in whatever is under them. Pressure on pavers should be moderate, because high pressure can blast out the joint sand. See the pressure washing pricing guide.
- Remove efflorescence and stains with products suited to the job. Gator's data sheet for its natural-look sealer calls for removing trapped efflorescence with a dedicated cleaner before sealing.
- Refill the joints. Gator's sheet says to remove contaminated jointing material and replace it with polymeric sand, then wait at least 48 hours at a minimum of 32 F with no rain for the sand to harden. It then calls for another 48 hours of dry weather, so the sand and the paver surface are dry. That is a two-day gap between sanding and sealing, so it is a second trip.
- New installs. SRW says to wait 28 days after installing polymeric sand before sealing. Gator says concrete pavers should only be sealed 60 days after installation. Both defer to the paver maker's recommendation. Follow the sheet for the product you use and the paver maker's advice.
Sealer coverage and coats
Coverage is the number that moves your materials cost the most. These come from data sheets for real sealers and are not endorsements.
| Product (data sheet) | Type | Coverage per gallon | Coats and timing |
|---|---|---|---|
| SRW LG Paver Seal (revised March 2021) | Water-based, low-gloss, film-forming | 150 sq ft | Second coat for a deeper sheen, after at least 4 hours. Wait 28 days after polymeric sand. |
| Gator Natural Look Signature Series (July 2025) | Water-based, non-film-forming | About 175 sq ft | One coat only. Spray in 60 sq ft sections and roll off the excess; the sheet says two people. Rain-safe after 24 hours. Use after 60 days on new pavers. |
| MORE Paver Sealer (2025) | Water-based penetrating | Up to 350 sq ft for a single coat, depending on the surface | Foot traffic after 6 hours, cure 24 hours. Apply when the surface is 50 to 80 F. |
The spread is a factor of more than two between a film-forming sealer and a penetrating one. Gallons = area x coats / coverage, plus about 10% waste. Porous, old or textured pavers take more. Test a small area first. All three sheets say to test in a hidden spot.
Conditions. Temperature windows differ by product: MORE says a surface temperature of 50 to 80 F, and Gator's natural-look sheet says air and surface between 32 and 85 F with the paver surface cool to the touch. Hot paving in sun is a problem for most sealers. See the weather rules guide for how to make the go or no-go call.
Production and dry time
No sealer maker publishes a production rate. What the sheets give you is the method and the waiting:
- Gator's best practice is two people, spraying 60 sq ft at a time and rolling off the excess.
- SRW wants 4 hours between coats for the highest gloss.
- MORE lists foot traffic after 6 hours and 24 hours to cure. Gator says rain-safe after 24 hours and to let it dry for 24 hours before use.
- Vehicles on a driveway need a longer wait. Check the sheet.
So time your own jobs in these buckets, and do not forget the dry time between steps, because it decides how many trips you make.
| Task | What you record |
|---|---|
| Wash and rinse | sq ft per crew-hour |
| Refill joint sand and compact | sq ft per crew-hour |
| Apply sealer, per coat | sq ft per crew-hour |
| Edge, detail and clean up | minutes per job |
| Trips | how many, and why |
The worked example uses placeholders of 1,000 sq ft per crew-hour to wash, 300 to refill joints and 600 to apply a coat.
Worked example: a 600 sq ft paver patio
The job: a 600 sq ft concrete paver patio, installed several years ago, dirty with some algae and washed-out joints. No old sealer. Wash, refill the joints with polymeric sand, wait for it to harden, then apply a low-gloss film-forming sealer in two coats. A two-person crew and two trips.
Placeholders: labor costs $32.50 per person-hour (a $25 wage plus 30% burden). Equipment is $15 per site hour. Overhead is 20% of price and profit is 15%.
Sealer: film-forming at 150 sq ft per gallon, two coats: 600 x 2 / 150 = 8.0 gallons, plus 10% waste is 8.8, so 9 gallons at $55 a gallon (a placeholder).
| Task | Rate | Crew-hours |
|---|---|---|
| Trip 1: drive and setup | allowance | 1.00 |
| Wash and rinse | 600 sq ft at 1,000 sq ft/crew-hr | 0.60 |
| Refill and compact joints | 600 sq ft at 300 sq ft/crew-hr | 2.00 |
| Trip 2: drive and setup | allowance | 0.75 |
| Seal, two coats | 1,200 sq ft of coats at 600 sq ft/crew-hr | 2.00 |
| Edging and cleanup | allowance | 0.50 |
| Total | 6.85 |
| Item | Amount |
|---|---|
| Labor, 6.85 crew-hours x 2 x $32.50 | $445.25 |
| Equipment, 5.85 site hours x $15 | $87.75 |
| Sealer, 9 gal x $55 | $495.00 |
| Polymeric sand, 4 bags x $32 | $128.00 |
| Cleaner, algae treatment, rollers and brushes | $52.00 |
| Direct cost | $1,208.00 |
| Price = $1,208.00 / 0.65 | $1,858 |
| Overhead share (20%) | $372 |
| Profit share (15%) | $279 |
That is $3.10 per square foot, all in. The number of bags of sand depends on paver size and joint width, so use the bag's coverage chart. The four here are a placeholder.
Now change one thing: use a penetrating sealer. Say it covers 350 sq ft per gallon in one coat, like the MORE sheet. That is 600 / 350 = 1.7 gallons, plus 10% is 1.9, so 2 gallons at $60 each. Sealing takes 1.0 crew-hour instead of 2.0.
| Item | Film-forming, 2 coats | Penetrating, 1 coat |
|---|---|---|
| Crew-hours | 6.85 | 5.85 |
| Labor | $445.25 | $380.25 |
| Equipment | $87.75 | $72.75 |
| Sealer | $495.00 | $120.00 |
| Sand and supplies | $180.00 | $180.00 |
| Direct cost | $1,208.00 | $753.00 |
| Price at 0.65 | $1,858 ($3.10 per sq ft) | $1,158 ($1.93 per sq ft) |
The choice of sealer moves the price by $700 on a 600 sq ft patio. Tell the customer which one you recommend and why: gloss and color enhancement, joint stabilization or a natural look.
Check it. At HomeAdvisor's $1.35 to $2.50 per square foot, 600 sq ft of concrete runs about $810 to $1,500, and Bob Vila's $1.25 to $1.75 for sealing alone is about $750 to $1,050. The penetrating price of $1,158 sits inside the first range and a little above the second, which makes sense because it includes the wash and the joint sand. The film-forming price of $1,858 is above both, because of the sealer and the second coat. If you are priced above your market, show the line items. If a competitor is cheaper, find out whether their price includes the wash, the sand and a second coat.
Concrete and driveways
A plain concrete slab or driveway is the same method with less prep: clean, repair cracks, seal. Differences:
- No joint sand. Control joints may need a sealant, which is a separate line.
- Cure time for new concrete. Follow the sealer maker's data sheet.
- Oil and tire marks. Degrease before you seal.
- Larger areas make the per-foot price drop, and the minimum matters less.
- Product choice. Acrylic, polyurethane and epoxy sealers have very different prices per gallon ($16 to $175 in HomeAdvisor's ranges).
Price a driveway from the same formula as the patio, and check it against the market range for concrete.
Upsell from a wash
The easiest way to sell a seal is on the wash visit. After the rinse, the customer sees what clean looks like and what it will look like in a year. Do this:
- Put it on the original quote as an optional line, "Add sealer, 600 sq ft."
- Show a before and after from your phone.
- Offer a package. Wash plus seal is cheaper than two separate trips, because you share the drive and setup.
- Say how long it lasts. MORE's sheet says expected wear is up to 3 years. Check the sheet for your product and tell the customer a range, not a promise.
Mistakes to avoid
- Sealing wet pavers or washed-out joints. Wait the full dry time.
- Sealing new pavers too soon. Check the paver maker and the sealer sheet.
- One sealer over another. SRW's sheet warns against it.
- Assuming one coat or two. The sheet says.
- Applying in hot sun or cold weather outside the product's range.
- Overapplying. Puddles of film-forming sealer turn white or sticky. Roll them out.
- Forgetting the rain-safe time. Check the forecast for 24 hours.
- Skipping the test patch.
- Pricing per square foot with no minimum. A 100 sq ft entry still needs two trips.
How Chalk helps
This part is about our software.
- Price book. Add a line for each service (wash, joint sand, seal) with the unit sq ft and a price per square foot, plus your minimum. Pick them onto a wash quote. See Send a quote and get it approved.
- Optional extra on a wash quote. Mark "Seal the patio" as an Optional extra, so the customer ticks it when they approve the wash.
- Waiting for dry time. The sand trip and the seal trip are two visits on one job. Book them both from Schedule a visit, and if rain pushes the sealing day, More > Rain day on the calendar moves it in one go, with nothing sent unless you tick Let the customers know.
- Photos. Upload Before and After photos to the job.
- Reseal reminders. Set the job type's Due again after to 36 months in Settings > Lists, and finished sealing becomes a lead on the funnel three years later. The repeat-work text to the customer is off until you turn it on in Settings > Automations.
Sources
Prices, rates and coverage change and vary by region. Check the current version of each source.
- HomeAdvisor: how much does it cost to seal concrete, updated June 20, 2026.
- Bob Vila: concrete cleaning and sealing services costs, updated February 9, 2023.
- SRW Products, LG Paver Seal technical data sheet, revised March 22, 2021 (srwproducts.com).
- Alliance Gator, Gator Natural Look Signature Series sealer technical data sheet, July 2025 (alliancegator.com).
- MORE Surface Care: paver sealer data sheet, 2025.