Free tool

Christmas light calculator for rooflines and trees

Measure the roofline, add any trees, and read off the strands, bulbs and clips to buy. Installers can switch on pricing and get a quote per foot.

Adrian GluchowskiOwner of Superior Stain Solutions, builder of ChalkLast reviewed

What you are doing
The house

Measure each run along the edge you will clip to. Use a tape or a measuring wheel on the ground, or count shingle courses.

Trees wrapped around the trunk

The lights spiral up the trunk. Put 0 trees if you have none.

The lights you are buying

Read these off the box. The numbers filled in are common, not a rule.

Power check (optional)

Leave watts blank to skip it. This is a planning number, not an electrician's sign-off.

Strands to buy

-
Lights to hang
-
To buy, with spare
-
Bulbs
-
Bulbs per strand
-
Clips
-

Power

Amps at 120 V
-
Circuits to plan on
-

The math

-

Lights are sold by the strand, but a house is measured in feet. This calculator turns the feet of roofline and the wraps around your trees into the number of strands, bulbs and clips to buy, with a spare share so a bad bulb or a bad cut does not stop the job. Every step of the math is printed under the answer, so you can check it against a tape measure.

If you hang lights for customers, switch the first box to Pricing a job for a customer. It adds your labor, your costs and your margin, and gives a price and a price per foot.

How the calculator works

  1. Runs. The feet of eaves and rakes, ridge, and any other straight run (windows, doors, a railing, a fence) added up.
  2. Trees. Each tree trunk gets a spiral. The wrap math is below.
  3. Lights to hang. Runs plus trees. Every length rounds up to a tenth of a foot, so the feet shown are the feet used.
  4. To buy. The lights to hang plus your spare share.
  5. Strands. The feet to buy divided by the length of one strand, rounded up to a whole strand.
  6. Bulbs. The feet to buy times 12, divided by the space between bulbs in inches, rounded up.
  7. Clips. The runs times 12, divided by how far apart you clip, plus the same spare share. Trees take no clips.
  8. Power (optional). Type the watts from the box and the page works out the load. See the notes below.

Measuring a roofline

  • Walk each edge and write it down. One line per run: front eave, back eave, each gable edge, the ridge. Add them up. Do not guess from the floor area of the house.
  • Measure along the edge you clip to, not the straight distance. A dormer, a bump-out or a step in the gutter adds feet.
  • Count both sides of a gable. Two rakes go up to the peak. People forget the second one.
  • Hang the ridge only if you want it. Some customers want the eaves and rakes only.
  • Add the extras last. Windows, doors, railings, posts and a walkway are "other runs". Measure the perimeter you plan to light.
  • Take photos of every side before you start. They help with the quote and show any damage that was already there.

For tape-free numbers, a measuring wheel on the ground or a laser distance meter held at the corner works. On a steep roof, never measure by climbing. Estimate from the ground and confirm on the first ladder visit.

Trees: the wrap math

A spiral around a trunk is longer than the trunk is tall. Unroll one turn and it is a right triangle: one side is the distance around the trunk (the circumference, which is pi times the width), the other side is how far the string climbs in that turn (the pitch, which is 1 divided by the turns per foot). The string for one turn is the long side of that triangle.

  • Circumference = 3.1416 x trunk width in inches / 12, in feet
  • Pitch = 1 / turns per foot, in feet
  • Feet for one turn = square root of (circumference squared + pitch squared)
  • Feet for one tree = height x turns per foot x feet for one turn

A wider trunk or a tighter wrap uses more lights. Wrapping the branches takes more again, and this calculator does not add it. For a full canopy, measure the string you plan to run along each branch and put it in "Other runs".

For installers: pricing per foot

Switch to Pricing a job for a customer and a second box opens. The price works like this:

  • Labor. The feet of lights times your install labor per foot, plus the same feet times your takedown labor per foot if takedown is part of the job.
  • Visits. The number of trips times your drive and setup cost per trip.
  • Materials. The strands you buy times what a strand costs per season, plus the clips times the cost of a clip. Enter 0 for lights if the customer owns them.
  • Price. Your cost divided by one minus overhead and margin, rounded up to the cent. If that is under your minimum job, the minimum is the price.
  • Per foot. The price divided by the feet of lights.

Overhead and margin are both shares of the price, the same as in the markup and margin calculator. The labor, trip and light costs filled in are starting points, not market rates. Use your own: the hourly rate calculator shows what an hour of your crew's time really costs, and the pricing guide for Christmas light installation covers leasing, takedown, storage and deposits. For when to sell, order, install and take down through the year, see the exterior contractor's year.

Power and safety notes

  • Watts come from the box. The calculator multiplies the strands you hang by the watts per strand you type in. It does not know your lights.
  • Amps are watts divided by volts. A US outlet is 120 volts.
  • The circuit limit is 1,440 watts by default. A 15 amp, 120 volt circuit is 1,800 watts. The National Electrical Code limits a continuous load, one that runs for three hours or more, to 80% of the circuit's rating, which is 1,440 watts. Lights on every evening count as continuous. Anything else on that circuit, such as a porch light or a garage outlet, uses part of the 1,440. If your circuit is different, or you are not sure, change the number or ask an electrician.
  • The maker's limit comes first. Each strand's label says how many sets can be joined end to end. Do not go past it, even if the circuit has room.
  • Use outdoor-rated lights and a GFCI outlet. The Consumer Product Safety Commission advises lights tested by a recognized lab and GFCI-protected outdoor outlets.
  • Falls are the real danger. Most decorating injuries are falls. Do not work alone at height. See the safety section of the installation pricing guide.

This page is a planning tool, not electrical advice. For anything beyond plugging in a few strands, have a licensed electrician look at it.

Worked example

The calculator opens on a house with 110 ft of eaves and rakes, a 40 ft ridge and 30 ft of other runs, plus two trees. The lights are 25 ft strands with a bulb every 12 inches. The spare is 10%, and a clip goes on every 12 inches.

  • Runs: 110 + 40 + 30 = 180 ft.
  • One tree: 10 ft tall, 8 inches across, 2 turns a foot. The circumference is 3.1416 x 8 / 12 = 2.094 ft, and the pitch is 1 / 2 = 0.5 ft. One turn is the square root of (2.094 squared + 0.5 squared) = 2.153 ft. There are 10 x 2 = 20 turns, so a tree takes 20 x 2.153 = 43.07 ft, which rounds up to 43.1 ft.
  • Two trees: 2 x 43.1 = 86.2 ft.
  • Lights to hang: 180 + 86.2 = 266.2 ft.
  • To buy: 266.2 x 1.10 = 292.82, which rounds up to 292.9 ft.
  • Strands: 292.9 / 25 = 11.72, so 12 strands.
  • Bulbs: 292.9 x 12 / 12 = 293 bulbs, and each 25 ft strand has 25 (12 strands of 25 is 300 bulbs if your lights come as strands).
  • Clips: 180 x 12 / 12 = 180, plus 10% is 198, so 198 clips.

Power. Say the box says 5 watts per strand. The strands that go up are 266.2 / 25 = 10.648, so the load is 10.648 x 5 = 53.2 W, or 0.44 A at 120 volts. That is 4% of a 1,440 watt circuit. If the same house used older strands at 100 watts each, the load would be 1,064.8 W, or 8.87 A, which is 74% of one circuit, and a second light set on that circuit would not fit.

The installer's price. With the starting points in the box: install labor $1.50 a foot, takedown labor $0.60 a foot, 2 visits at $40, lights at $18 a strand per season, clips at 6 cents, 20% overhead and a 15% margin.

ItemMathAmount
Install labor266.2 ft x $1.50$399.30
Takedown labor266.2 ft x $0.60$159.72
Drive and setup2 visits x $40$80.00
Lights12 strands x $18$216.00
Clips198 x $0.06$11.88
Your cost$866.90
Price$866.90 / (1 - 0.20 - 0.15)$1,333.70
Overhead (20% of the price)$266.74
Profit$1,333.70 - $866.90 - $266.74$200.06

That is $5.01 per foot of lights, and the profit is exactly 15% of the price. The minimum job of $300 does not apply. A small porch with 25 ft of lights is a different story. Its cost works out to $170.18 and its calculated price to $261.82, so the $300 minimum is the price. That is $12.00 a foot, and the profit is 23.3% instead of 15%, because the minimum is set above what a very small job works out to.

Tips

  • Buy the spare. A strand that fails in week two costs a service call. 10% is a common starting point, not a rule.
  • Match the spacing to the look. Close-set bulbs look fuller and use more lights per foot. Compare the bulbs per strand before you compare the strand prices.
  • Test every strand on the ground, before it goes up.
  • Check the count of strands that can connect before you plan a long run.
  • Photograph the plug-in point, so you know where the power comes from at takedown.
  • Quote takedown in writing. If it is not in the price, say so, and say what it costs.

FAQ

How many Christmas lights do I need for my house?

It depends on the feet you are lighting and how close the bulbs are. Measure the roofline, enter the bulb spacing and strand length from the box, and the calculator gives the strands and bulbs. The numbers in it when the page loads are an example, not an average.

How many feet of lights per tree?

It depends on the height, the width of the trunk and how tight you wrap. The example in this page is 43.1 ft for a 10 ft tree, 8 inches across, wrapped twice a foot. A skinnier trunk or a looser wrap needs less.

How do I measure my roofline for lights?

Walk each edge you want lit, write down the length, and add the runs. Count both rakes of every gable. Measure from the ground with a wheel or a laser meter, and do not climb to measure.

How many strands of lights can I plug together?

The label on the strand says. It is the maker's limit for that product. Do not go over it, even if your circuit can carry more.

How much should I charge to hang Christmas lights?

Work it from your own costs. Switch the calculator to pricing a job and enter your labor, trips, light costs, overhead and margin. For market ranges, takedown and storage, see the pricing guide.

Does this include the lights I already own?

Set the light cost per strand to 0 when the customer owns the lights. Install labor and your other costs still count.

Is my data saved?

No. The numbers stay in your browser, and nothing is sent anywhere.

Sources

  • Consumer Product Safety Commission, Make it a home safe home for the holidays: outdoor-rated lights tested by a recognized lab, GFCI-protected outlets, and the injury figures for holiday decorating, including falls.
  • National Fire Protection Association, NFPA 70, the National Electrical Code: the rule for continuous loads (section 210.20) that limits a circuit to 80% of its rating when the load runs three hours or more. The edition your area has adopted decides the details.
  • OSHA, 29 CFR 1926.1053, ladders.
  • The wrap length is plain geometry, the Pythagorean theorem applied to an unrolled turn of a spiral.
  • Bulb spacing, strand length, the spare share, clip spacing, and every labor, trip, light and clip cost in the installer box: starting points to replace with your own numbers, not published figures.