Free tool

Gutter cleaning price calculator

Enter the feet of gutter, the height, how full they are and your downspouts. You get hours, a price at your margin and a price per foot.

Adrian GluchowskiOwner of Superior Stain Solutions, builder of ChalkLast reviewed

The gutters
Pace

Typical starting points, adjust to your crew. Time a few jobs and put in your own numbers.

Your numbers

Price

-
Price per foot
-
Labor hours
-
Job cost
-
Profit
-
Margin
-

Where the time goes

Gutter runs
-
Downspouts
-
Setup and travel
-
Height and debris factor
-

Gutters are priced by the foot and lost on the ladder. A single story house with light leaves is an easy hour. A three story house under oak trees is a morning of moving ladders and hauling wet debris. If you quote both at the same price per foot, you are giving the second one away. This calculator starts from feet, then stretches the time for height and for how clogged the gutters are, so the price follows the work.

How the calculator works

  1. Feet of gutter. Add up every run you will clean. The pace is set per foot, so the more feet, the more time.
  2. Height. Two and three story gutters take longer, because the ladder moves more often and every move is slower and more careful. The calculator multiplies the time by a factor for the number of stories (1.4 for two and 1.9 for three to start with).
  3. Debris. Light debris is quicker than normal, and packed gutters with plants growing in them take much longer. The factors are 0.75 and 1.6 to start with.
  4. Downspouts. Each one is checked and flushed, which takes a few minutes. They are added as their own time.
  5. Hours. Feet divided by your pace, times the height and debris factors, plus downspouts. Add travel, setup and cleanup. The total rounds to the nearest tenth of an hour, and that is what gets priced.
  6. Price. Labor plus supplies is your direct cost. The price is that cost divided by one minus overhead and margin. If the work comes in under your minimum charge, the price is the minimum.

The formula

  • Run hours = feet / feet per hour x story factor x debris factor
  • Downspout hours = downspouts x minutes each / 60
  • Hours = run hours + downspout hours + setup, rounded to a tenth
  • Price = (hours x labor cost + supplies) / (1 - overhead% - margin%), or your minimum if that is higher
  • Price per foot = price / feet

Worked example

The calculator opens on a two story house with 160 feet of gutter and 4 downspouts, normal debris. Your pace on one story is 100 feet an hour, each downspout takes 5 minutes, and travel, setup and cleanup take an hour. Labor costs $32.50 an hour, overhead is 15%, the margin is 25%, supplies are $5 and the minimum is $100.

  • Runs: 160 / 100 = 1.6 hours, times 1.4 for two stories = 2.24 hours.
  • Downspouts: 4 x 5 minutes = 20 minutes, 0.33 hours.
  • Hours: 2.24 + 0.33 + 1.0 for travel, setup and cleanup = 3.57, which rounds to 3.6 hours.
  • Cost: 3.6 x $32.50 = $117 of labor, plus $5 of supplies, is $122.
  • Price: $122 / (1 - 0.15 - 0.25) = $203.33, which the calculator rounds up a cent to $203.34 so the margin is never short. Overhead is 15% of that ($30.50), so the job costs you $152.50 and leaves $50.84, which is 25%. The price per foot is $1.271, inside the $1.25 to $2.50 a foot that the gutter cleaning pricing guide cites for two stories.

How the price moves with the job:

JobHoursPricePer foot
160 ft, two stories, normal debris3.6$203.34$1.271
Same house, light debris3.0$170.84$1.068
Same house, heavy debris4.9$273.75$1.711
120 ft, one story, 3 downspouts2.5$143.75$1.198
200 ft, three stories, 6 downspouts5.3$295.42$1.477

A small job and the minimum. A one story porch with 40 feet of gutter and one downspout works out to 1.5 hours and $89.59. With a $100 minimum, the price is $100, and the margin is about 31%. A minimum should feel high on small jobs, because travel and setup cost the same as on a big one.

This calculator's starting numbers are typical defaults and differ from the worked example in How much to charge for gutter cleaning; put in your own.

Pricing tips

  • Price the house, not the foot. Per-foot prices are how people compare, but the real driver is hours. Use the calculator for the total, and quote the price per foot only if the customer asks.
  • Measure from the ground. Walk the roof edge with a measuring wheel or tape, or take the run lengths from a photo or the plans. Count the downspouts at the same time.
  • Ask about the trees. Overhanging trees, pine needles and shingle grit decide the debris factor. A photo of the gutters from the customer is worth a lot before you quote.
  • Put height on the quote. Customers understand that two stories cost more than one. Showing it keeps you from discounting the hard houses.
  • Offer the follow-up. A second visit after the leaves are down, or a yearly plan, is the best way to turn a one-off into regular work. Check what any discount does to your margin first.
  • Sell the add-ons separately. Flushing the downspouts, cleaning the fascia, small repairs and guards are separate lines.
  • Watch the season. Most gutter work clusters after leaf fall and in spring. Book it ahead and group stops by street to keep your drive time down.

Ladder safety

Gutter work puts you on a ladder all day, which is where most of the risk is. The OSHA ladder standard is a good rule of thumb even where it does not strictly apply to your work. A leaning ladder should be set so its base is about one quarter of its working length out from the support, and a ladder used to reach a roof edge or landing should extend at least 3 feet above it, or be secured at the top. Set it on firm, level ground, look for power lines before you raise it, and move it instead of reaching. If the pace you quote depends on stretching off the side of a ladder, it is the wrong pace.

Common mistakes

  • One price per foot for every house. Height and debris change the time more than the length does.
  • Forgetting the downspouts. A clogged spout is half the point of the visit, and it is the part that takes the surprise minutes.
  • No minimum. A short run takes the same truck, ladder and setup as a long one.
  • Not charging for hauling. Wet debris is heavy and messy. If you bag it and take it, put the bags and dump fees in supplies.
  • Using your best day as the pace. Your pace should be an average over several jobs, with the hard ones in it.

FAQ

How much should I charge to clean gutters?

Work it out from your costs. Put your labor cost, overhead and margin into the calculator with the feet, height and debris for the job. It gives you a price and a price per foot at your margin. Another company's per-foot price hides their costs and pace, so do not copy it.

Should I price gutter cleaning per linear foot or per job?

Think in hours, quote in whatever the customer finds easier. Many customers ask for a price per foot, but a flat price for the house is simpler to approve. A flat price is also easier to defend when the debris is worse than it looked.

How long does it take to clean gutters?

It depends on the height, the debris, your tools and your crew. The 100 feet an hour for one story is a starting point, not a published figure. Time your own jobs and use the averages.

Do I charge extra for a second or third story?

Yes. The calculator does it with a time factor, which flows into the price. Set your own factors from your own jobs.

Should I include the downspouts?

Yes. Each one is a few minutes of checking and flushing. If you leave them out of the price, you pay for them yourself.

What if the gutters are packed?

Use the heavy setting, which takes 1.6 times as long to start with. If the gutters are full of growth or need repairs, quote the extra work as its own line.

Does the calculator include sales tax?

No. Whether gutter cleaning is taxable depends on your state and sometimes your city. Ask your state revenue department or your accountant.

Sources

  • Occupational Safety and Health Administration, 29 CFR 1926.1053, Ladders: the rule on setting a leaning ladder so its base is about one quarter of the working length from the support, and on extending a ladder at least 3 feet above an upper landing.
  • Feet an hour, the height and debris factors, minutes per downspout, supplies and setup time: typical starting points, not published figures. Adjust them to your crew and your market.