Pricing guide

How much to charge for gutter cleaning

Price gutter cleaning by the linear foot, story and debris level, with minimums, downspouts and guard work, and a worked two-story example.

Adrian GluchowskiOwner of Superior Stain Solutions, builder of ChalkLast reviewed 12 min read

On this page

Gutter cleaning looks like a simple job: a ladder, a scoop, a hose. The price is simple too, until a house has three stories of trees over it, a clogged underground drain and a customer who wants it done on the one rainy Friday you cannot get a ladder on wet ground.

This guide shows how to price gutter cleaning from your own costs. You will measure feet and stories, set a rate for debris, charge for downspouts and extras, set a minimum, and check the answer against what customers read online. It ends with a worked two-story example, a solo version of the same job, and the safety rules that decide whether you should take the job at all.

What homeowners see online

Customers have read a cost guide before they call. Here are two recent ones.

WhatLeafFilter (updated June 2026)TaskRabbit (updated October 2026)
Per linear foot, all homes$0.95 to $1.25$0.80 to $2.00
One story, per linear foot$0.70 to $1.30not split out
Two story, per linear foot$1.25 to $2.50not split out
A whole home$191 to $529$120 to $300 for 150 to 200 ft
One story / two story / three storynot split out$130 to $250 / $150 to $350 / $200 to $450+
Flush downspoutsnot listed$50 to $100
Clear debris off the roofnot listed$50 to $150

LeafFilter's cost guide is written by a gutter guard seller, so read it as a market snapshot and not as neutral advice. It also lists surcharges as percentages: 5% to 10% more for hard-to-reach landscaping, 10% to 50% more for gutters in poor condition, 15% more for a steep roof, and a cost that "often doubles" at three stories or more.

TaskRabbit adds that heavy clogs, gutter type (K-style, half-round, box), seamless or seamed runs and recurring service all move the price. It lists gutter guard installation at $7 to $15 per linear foot, which is a different job, not a cleaning price.

These are national averages. Use them as a check after you build your price, never to set it.

Measure feet, stories and pitch

Price from the run of gutter, not from the size of the house.

  1. Linear feet. Walk the eaves and add up every run. A simple rectangle house is two long eaves and two short ones, but add dormers, bump-outs and garages, which have their own gutters. If you cannot walk it, a satellite photo and a tape on the ground works for a quote, then confirm on site.
  2. Stories. Count the height of each run, not the house. A ranch with a two-story wing is two prices.
  3. Roof pitch and surface. A steep or slick roof means you stay on the ladder and move it more.
  4. Downspouts. Count them. Note which ones go to an underground drain, which ones have a leader or extension, and which ones are wired shut by years of leaves.
  5. Gutter type and guards. Open K-style gutters are the base price. Guards, covers and screens change the job: you may need to lift them and put them back.
  6. Access. Shrubs against the wall, a fence in the way, a steep side yard, no soft ground for ladder feet.
  7. Debris. Photograph a couple of spots. Look for seedlings, moss, shingle grit and standing water.

Write the linear feet, stories and debris level on the quote. That sentence is what you point to when a customer says "it was only a few leaves."

Production rates

Nobody publishes a standard rate for gutter cleaning, and what you will find is anecdotal.

The best public data point is a contractor on the Pressure Washing Resource forum who bid a retirement home with 2,548 feet of gutter (2,110 feet on the second story and 438 on the first). He planned three 8-hour days for himself and one helper, working up and down a ladder, scooping, vacuuming and then rinsing. That is about 24 crew-hours, or roughly 106 feet per crew-hour. His per-foot bid was $1.50 on the second story and $0.75 on the first, against $120 an hour if the customer wanted hourly. It is one man's plan, not a measured result, and he added that a job running past 10 hours "probably ain't worth it."

Others on the same thread said that walking a walkable roof with a blower can turn a three-day ladder job into a half day, and another said one person on a lift can beat three on ladders. Method is the biggest lever on your production.

Start your own table like this and fill it in over your next ten jobs:

TaskWhat you recordStarting point (replace it)
Ladder, scoop, rinse, one storyfeet per person-hourabout 100
Ladder, scoop, rinse, two storyfeet per person-hourabout 60 to 70
Blower from the roof (dry leaves, walkable)feet per person-hourtime it
Pole vacuum from the groundfeet per person-hourtime it
Flush one downspoutminutes eachabout 5
Move a ladderfeet per move, seconds per movetime it

The numbers in the last column are placeholders for the worked examples below. They are not benchmarks.

Debris and downspouts

Debris is the main reason one gutter takes twice as long as the next. Set three levels and write them on your price list:

LevelWhat it looks likeHow to price it
LightDry leaves, a little grit, flows freelyYour base rate
ModerateWet packed leaves, some seedlingsBase rate plus 25% to 50%, or time-and-materials
HeavyMoss, mud, standing water, plants growingHourly, or a flat price after you have seen it

Those percentages are a starting point to set from your own time log. LeafFilter's 10% to 50% range for gutters in poor condition is a decent outer fence.

Downspouts are priced separately from the run. A downspout that flows when you pour water in it is a few minutes. A clogged one is a tool job: a plumber's snake, a hose from the bottom, a leaf blower. Price a flush as a line item. TaskRabbit lists $50 to $100 for downspout flushing as a service. If a downspout goes to an underground drain that is blocked, that is a drain problem, not a gutter problem. Say so, and do not promise to fix it.

Disposal is real cost. Bagging wet leaves, hauling and tipping fees are a line in your cost, even when the customer lets you leave debris on their lawn. Take photos before you leave it.

Minimums and drive time

A small job still costs a trip, a ladder setup and a cleanup. Work out your minimum from your own costs.

For a solo operator: 0.5 hours of drive, 0.25 of setup, 0.5 of cleaning and 0.25 of cleanup is 1.5 hours.

ItemAmount
Labor, 1.5 h x $32.50$48.75
Equipment, 1.0 site hour x $10$10.00
Bags and supplies$5.00
Direct cost$63.75
Price = $63.75 / 0.65$98

So a $100 minimum is the floor in this example, and a market with higher wages or longer drives needs more. For a check: TaskRabbit shows $80 to $150 for a small home with about 100 feet of gutter.

Drive time matters more here than in most trades, because the jobs are short. A route of five houses on one street is a good day. Five houses in five towns is not.

Add-ons: guards, flushing and roof blow-off

These are the upsells that make a gutter route pay, and they are also where jobs go wrong.

  • Downspout flushing or clearing. A line item per downspout.
  • Roof debris blow-off. Often what filled the gutters is still on the roof. Blowing it off first is faster than scooping it twice. TaskRabbit lists roof debris removal at $50 to $150. Only do this when the roof is safe to walk, and see the safety section.
  • Minor repairs. Re-hanging a loose section, re-sealing a corner, adding a downspout extension. TaskRabbit lists sealing leaks at $50 to $125 and an extension at $30 to $60. Price repairs by time and materials, not as part of the cleaning.
  • Guards. Lifting, cleaning under and replacing guards takes longer than open gutter. Price per foot with a surcharge, and do not clean guards you did not install without saying so in writing. A guard that cracks when lifted is your fault.
  • Photos. A before and after photo of each side is the best proof of work you have. It also covers you when someone says a gutter was already loose.
  • A second visit. Twice a year is common for houses with trees: late spring and late fall. Offer the second visit up front at a slightly lower price. It saves you a quote and a drive.

Worked example: 180 ft, two stories

The job: a two-story house with 180 feet of open K-style gutter, six downspouts, moderate debris, no guards. A two-person crew: one on the ladder, one on the ground rinsing and moving buckets.

Placeholders: labor costs $32.50 per person-hour (a $25 wage plus 30% burden). Equipment is $10 per site hour. Overhead is 20% of price and profit is 15%. The crew's pace is 120 feet per crew-hour for a two-story run, including ladder moves.

TaskRateCrew-hours
Round-trip driveallowance1.00
Setup, ladders, tarpsallowance0.25
Clean and rinse 180 ft180 ft at 120 ft/crew-hr1.50
Flush six downspouts6 at 5 minutes0.50
Bag, haul, cleanup, photosallowance0.50
Total3.75
ItemAmount
Labor, 3.75 crew-hours x 2 people x $32.50$243.75
Equipment, 2.75 site hours x $10$27.50
Bags and supplies$20.00
Direct cost$291.25
Price = $291.25 / 0.65$448
Overhead share (20%)$90
Profit share (15%)$67

That is $2.49 per linear foot. LeafFilter's two-story range is $1.25 to $2.50, so this sits at the very top of it. TaskRabbit's range for a two-story home is $150 to $350, so it is above that too.

Now run it solo. One person works the same house at 70 feet per hour: 180 / 70 = 2.57 hours. Add 1.00 of drive, 0.25 of setup, 0.50 of downspouts and 0.50 of cleanup for 4.82 hours.

ItemAmount
Labor, 4.82 h x $32.50$156.70
Equipment, 3.82 site hours x $10$38.21
Bags and supplies$20.00
Direct cost$214.91
Price = $214.91 / 0.65$331

That is $1.84 per linear foot, and it sits inside both ranges. In these placeholders, a second person makes the job 1.7 times faster (120 vs 70 feet per hour) but doubles the labor, so a solo price wins. A helper pays for themselves only when they make you more than twice as fast, or when the job is too dangerous to do alone. That is a question your time log answers, not a guess.

What to say on the quote: "Clean 180 linear feet of gutter on two stories, flush six downspouts, bag and remove debris. Includes before and after photos. Gutters in good repair. Repairs and guard work are quoted separately."

Ladder safety and insurance

A fall from a ladder is the worst thing that can happen on this job. Make these rules non-negotiable:

  • Set the ladder at the right angle. For straight and extension ladders, OSHA's rule is to set the base about one quarter of the ladder's working length (foot to top support) out from the wall, about 75 degrees. When a ladder reaches a roof or other landing, the side rails should extend at least three feet above it. Check the current text of 29 CFR 1926.1053 for the details.
  • Three points of contact. Face the ladder and keep a hand and two feet or two hands and a foot on it while you climb. Hoist tools. Do not carry them up.
  • Firm ground and tie-off. Never set feet on loose objects, soft soil or a wet deck. Use ladder levelers and tie off where you can.
  • Power lines. Look up before you raise a ladder. Use a fiberglass (nonconductive) ladder near any wires. OSHA requires people who are not trained electrical workers to keep themselves and anything conductive they hold, ladders included, at least 10 feet from overhead lines up to 50 kV (29 CFR 1910.333(c)(3)), and requires nonconductive side rails where a ladder could touch live equipment (29 CFR 1926.1053(b)(12)). Treat the service wire to the house as live.
  • Do not work alone on a tall ladder if you can avoid it. At minimum, tell someone where you are.
  • Do not walk a roof you cannot walk. Wet shingles, moss, steep pitch and metal are not safe. A pole vacuum from the ground costs more per hour and risks no one's neck.
  • Know when to say no. Three stories, a tile roof, a tree you cannot get around and a customer who pressures you to rush are good reasons to decline or refer the job.

Check your insurance before you add a ladder trade. General liability should cover damage to the house; workers' compensation covers employees. Ask your agent about falls from height, because some policies limit it. This is not legal or insurance advice.

Mistakes to avoid

  • Pricing by the house, not by the run. Feet and stories set the time.
  • No debris level on the quote. Write it down, with a clause for heavy clogs.
  • One price for every story. A two-story run takes longer per foot. LeafFilter's own data shows it.
  • Skipping the downspouts. The water has to go somewhere. Include a flush, or say you do not.
  • Cleaning guards you did not install without a note. If one breaks, you own it.
  • No minimum. A short job still costs a trip.
  • Weather. Wet ground and wet ladders are a safety call, not a scheduling inconvenience.
  • A helper you cannot afford. Time a solo and a two-person day before you assume two is better.

How Chalk helps

This part is about our software.

  • Price book by the foot. Add your gutter lines to the price book with a unit of linear foot (the unit list also has square foot, each, hour, gallon and room), one for each story, and your minimum as a line of its own. Pick them on the quote and change the quantity. See Send a quote and get it approved.
  • Optional extras. Mark downspout flushing, roof blow-off or a second visit as an Optional extra so the customer ticks what they want.
  • Twice a year. Book the fall visit and the spring visit as a repeating series from the job: Every 6 months is one of the choices under Repeats. Chalk books the whole run at once (up to 60 visits). It does not add more later on its own, so book another run when it runs low.
  • Photos on the job. Upload Before and After photos to the job from your phone.
  • Rain day. Gutter work is weather work. On the calendar, More > Rain day moves every visit on a wet day to the next open day, or a number of days later, or to Waiting. Nobody gets a text unless you tick Let the customers know. In Settings > Lists you can mark a job type as outside work, so it shows a Weather tag.

Want to check your hourly cost first? Use the hourly rate calculator. Not sure whether you are adding markup or margin? See the markup and margin calculator.

Sources

Prices and rates change and vary by region. Check the current version of each source.