Pricing guide

How to price drywall repair for handymen and painters

Price drywall patches by size tier, texture and ceiling height, set a minimum, and bundle patch and paint, with timed steps and a worked example.

Adrian GluchowskiOwner of Superior Stain Solutions, builder of ChalkLast reviewed 10 min read

On this page

Drywall repair is a drying job. The patch itself takes minutes. The compound has to set or dry before the next coat, the next coat has to dry before you sand, and the sanded patch has to be primed before it will take paint. A hole that takes 20 minutes of hands-on work can take three trips. The contractors who lose money on drywall are the ones who priced the 20 minutes.

This guide shows how to price drywall patches by size tier, how many trips each tier needs, what the data sheets say about drying, how to handle texture and ceilings, what a fair minimum looks like and how to bundle patch and paint. It ends with a worked example, safety notes for older homes, and the mistakes that cost the most.

What homeowners see online

Fixr's drywall repair guide (updated January 2025) gives this picture:

WhatFixr's range
Typical repair, whole job$200 to $550 (average $350)
Hourly labor$70 to $80 (up to $100 for complex repairs)
Minimumone hour for small projects
Hole$60 to $200
Anchor hole$75 to $105
Ceiling hole$75 to $115
Nail pop$75 to $140
Crack$60 to $330
Torn paper$95 to $300
Corner crack$220 to $315
Water damage$400 to $800
Retexture$1 to $3 per sq ft

Fixr's page also lists some odd per-square-foot figures, so read it for the repair types and the hourly rate. Another consumer marketplace, Thumbtack, says professionals' rates start at $75 an hour for repairs and texturing.

Most of these prices describe a quick job with one visit. The multi-visit repair that gets a flat finish is a different, more expensive job. That gap is where your quote needs to be clear.

Size tiers

Price by tier, so you can quote on the phone from a photo.

TierWhat it isMethodTrips
1Nail pops, dings, anchor holesReset the screw or fill, one or two coats, sand1 to 2
2Hole up to about 3 inchesMesh or patch, setting compound, topping coat2
3Hole from 4 to 12 inchesBacking, cut-in piece or patch kit, three coats3
4Hole from 12 inches to about 2 feetCut-in piece fastened to the framing or a backer, tape, three coats3
5Bigger, wet, moldy or structuralQuote by the hour after you open it upvaries

Tier 5 is a different job. Wet drywall means finding the water, cutting out all the damaged board and often a mold question. Do not flat-price what you cannot see.

The steps and the drying time between them

A good patch follows the same sequence:

  1. Prep. Cut back loose or crumbling board to sound edges, square the hole, add backing where there is none.
  2. Fill and embed. Fit the patch, embed tape or mesh in compound, and fill the void.
  3. Second coat. Wider than the first, to hide the edge.
  4. Finish coat. Wider again, thin, smooth.
  5. Sand. Controlled dust.
  6. Texture, if needed.
  7. Prime. New compound soaks up paint unevenly and shows through as a dull spot (flashing).
  8. Paint.

What the makers say about timing.

  • Setting-type compound (the powder you mix, sold by working time such as 20, 45 or 90 minutes). National Gypsum lists working times of 5, 20, 45, 90 and 210 minutes. USG's data sheet explains the difference that matters: working time is how long you can spread it, setting time is when it has hardened enough for the next coat. A 20-minute bag is not ready in 20 minutes. It stays workable for about that long and sets in a time near it. Once it has set you can recoat without waiting for it to dry, but it is hard to sand, so USG says to smooth it before it hardens or while it is damp but hardened.
  • Ready-mix compound dries by evaporation. Fine Homebuilding says that under good conditions it dries within 24 hours, with an application temperature of at least 55 F, and that three coats are typical for a full taping job. National Gypsum gives 55 to 95 F as the working range for its ready-mix products.
  • Temperature. USG's setting-type sheet says to keep air, water, mix and surface temperature at a minimum of 55 F until joints are completely dry.
  • Painting and texturing. USG's sheet does not recommend painting or texturing before the compound has set, and it says to prime once it has hardened and let the primer dry.

A common approach is setting compound for the fill and embed coats, which can go on the same day, and ready-mix for the topping coat, which is easier to sand and needs overnight. That is why a patch done properly is usually two or three trips. Price the trips.

Texture matching

If the wall or ceiling is textured, the patch is not finished until the texture matches. Orange peel, knockdown, skip trowel and popcorn all need a different method and tool.

  • Test first. Practice on cardboard or a scrap of board and compare in raking light.
  • Small areas are often matched with aerosol texture; larger areas call for a hopper gun and compressor.
  • Texture goes on after the patch is sanded and before primer, and it needs to dry before you prime.
  • Price it as its own line. In the example below, texture matching is 0.75 hours plus $12 of material, so about $75.

Texture matching is the part customers cannot see in advance and the part that tells them whether you are good. Say what you can promise: "close match." A perfect match on an old texture is not something you can guarantee.

Ceilings and height

Working overhead is slower, messier and harder on the body. Add to your hours, not to the price after the fact:

  • Ceiling work: add about 25% to the hours as a starting point, and replace it with your own number after you time a few.
  • Heights above a step ladder (stairwells, vaulted ceilings) mean scaffold or a ladder setup, which is time and sometimes rental. Fixr's price for a vaulted ceiling repair is $400 to $1,000.
  • Dust control. Ceilings drop it on everything. Plastic and a vacuum on the sander add time.

Minimum charge

A single nail pop still costs a trip, setup and cleanup. Fixr lists a one-hour minimum for small projects. Build yours from your own numbers.

With the placeholders used below ($80 an hour, a $40 trip charge, a 30% markup on materials), a tier-1 job of 0.75 hours and $3 of materials comes to 0.75 x $80 + $40 + $3.90 = $103.90. A $125 minimum covers one hour of work and a trip with room to spare, and it sits inside the range that other handyman guides use.

Patch and paint bundles

A patched wall that is not painted is unfinished. Customers do not want to hire two people. Offer bundles:

  • Patch only. The customer or a painter does the paint. Say that the patch will show without primer and paint.
  • Patch, prime and spot paint. Spot painting rarely hides a patch. Be honest about that.
  • Patch and repaint the wall (or the ceiling). Paint the whole wall to the corners. This is the finish that looks right.

Price the paint from interior painting production rates. See How to price interior painting for the measured-rate tables.

Worked example: living room patch and paint

The job: in a 12 by 14 foot living room with 8 foot ceilings, patch an 8 inch hole (tier 3), a 3 inch hole (tier 2), six nail pops (tier 1) and a 2 by 2 foot ceiling patch (tier 4, with orange-peel texture to match). Then repaint the patched wall and the whole ceiling.

Placeholders: $80 an hour, a $40 trip charge, materials marked up 30%. Production rates for painting are the middle of those in the interior painting guide: 175 sq ft per hour for walls and 200 for ceilings, per coat.

Part 1: the repair, three trips.

TripWorkHours
1Cut and fit both wall patches with backing. Pull and screw nail pops. Cut the ceiling patch and back it. First coat of setting compound on all of it.2.00
2Second coat on everything, feathered wider.1.25
3Finish coat, sand with dust control, spray orange-peel texture on the ceiling patch, spot prime.1.50
Total4.75
ItemAmount
Labor, 4.75 h x $80$380.00
3 trips x $40$120.00
Materials, $42 + 30%$54.60
Repair total$554.60, call it $555

Part 2: paint, one more trip. Wall: 12 ft x 8 ft = 96 sq ft, two coats. Ceiling: 12 x 14 = 168 sq ft, two coats.

TaskRateHours
Wall, two coats96 x 2 = 192 sq ft at 175 sq ft/hr1.10
Ceiling, two coats168 x 2 = 336 sq ft at 200 sq ft/hr1.68
Mask, cut in, cleanupallowance0.72
Total3.50
ItemAmount
Labor, 3.5 h x $80$280.00
1 trip$40.00
Paint and supplies, $87 + 30%$113.10
Paint total$433.10, call it $433

The bundle: $555 + $433 = $988.

Check it against the tier prices. Priced separately at the formula (hours x $80 + trips x $40 + materials x 1.3), the tiers would come to $125 for tier 1 (the minimum), $210 for tier 2, $340 for tier 3 and $480 for tier 4, which is $1,155 for the repair alone. The bundle repair price is $555 because the four repairs share trips and a drive. Sharing trips is the discount. Fixr's typical repair range is $200 to $550, so the repair part is at the top of it and includes a ceiling patch with texture.

Tier price list at the same placeholders:

TierHoursTripsMaterialsPrice
1: nail pops, up to 60.751$3$125 (minimum)
2: hole up to 3 in1.502$8$210
3: hole 4 to 12 in2.503$15$340
4: hole 12 in to 2 ft4.003$30$480
Texture match, add0.75$12$75
Ceiling or over 10 ft, add25% of hourson the hours

Fixr's "hole" range of $60 to $200 and its ceiling hole range of $75 to $115 are lower than tiers 2 and 3. They describe a single-visit job with a quick finish. If a customer shows you a lower quote, ask whether it includes three coats, sanding, primer and texture.

Safety in older homes

  • Lead paint. If the home was built before 1978 and your sanding disturbs more than 6 square feet of painted interior surface, the EPA's Renovation, Repair and Painting rule can apply. The small-job limit never covers window replacement, demolition, or prohibited practices such as open-flame burning or power sanding without HEPA dust collection. See the EPA contractor page and the EPA exception for minor work. This is not legal advice. Check your state's rules too.
  • Asbestos. The EPA lists textured paint and patching compounds among the older building materials that may contain asbestos. You cannot tell by looking. If the ceiling texture or old compound might be that old, do not sand or scrape it; get it tested first. See the EPA asbestos pages for current guidance.
  • Dust. Use a vacuum-attached sander or a damp sponge, and a mask rated for fine dust.
  • Water damage. Find and fix the source before any patch. A patch over a leak fails and is your callback.

Mistakes to avoid

  • Pricing the 20 minutes. Price the trips and the drying.
  • Recoating before it is dry or set. Wet compound sinks and cracks.
  • Skipping primer. Patches flash through paint.
  • Promising a perfect texture match.
  • Flat-pricing water damage.
  • No minimum or trip charge.
  • Patching over a leak.
  • Sanding painted walls in an old house without checking.
  • Quoting one price for patch and paint without saying which wall and ceiling you will paint.

How Chalk helps

This part is about our software.

  • Price book tiers. Add a price-book item for each tier with the unit each, plus items for texture matching, a ceiling add-on and your minimum. Pick them onto a quote in a tap and set the count. See Send a quote and get it approved.
  • Optional extras. Mark texture matching, paint and prime as Optional extras so the customer ticks what they want. A patch-only price and a patch-and-paint price on the same quote makes it easy to say yes.
  • Several visits on one job. A repair that needs three trips is a job with several visits. Book each trip as its own visit on the calendar from the job (Schedule a visit), and the crew sees every visit on their phone.
  • Photos. Upload Before and After photos to the job, which is the best proof of the starting condition.
  • Quote templates. Save "patch and paint, one room" as a quote template under Settings > Quote templates.

Sources

Prices and rates change and vary by region. Check the current version of each source.